Jump to content
SAU Community

Recommended Posts

Not sure on costs but Mobile Injector Service can do highflowing. I reccomend spending the money and buying bigger injectors tho.

What are some reasons to upgrade to bigger injectors apart from just having a newer item in there?

when your stock injectors cant flow enough fuel to your engine from either turbo increase or just boost pressure you need more fuel to equal the amount of air going in on a ratio.I woulnd tget hi flow ones my old man has had bad expericence with them.I just buy new ones and so be it plus there nto that expensive now, you can get 555cc nismo ones for aound 750 to 850 a set

when your stock injectors cant flow enough fuel to your engine from either turbo increase or just boost pressure you need more fuel to equal the amount of air going in on a ratio...

Yeah i knew that bit :P

...I woulnd tget hi flow ones my old man has had bad expericence with them...

What kind of bad experience? what happened?

stock rb25det injectors can be highflowed to approx 650cc with out losing their spray pattern once u go bigger than that ur pattern starts going all over the shop. Mobile Injector Services do these and i think they're roughly $400 and the injectors are pretty much brand new.

Yeah i knew that bit :laugh:

What kind of bad experience? what happened?

Well basically the guy who did these ones,( dont want to name anyone except he is from towommba area) didnt do a very good job of them plus its a bit ruthless to do them.The spray pattern is crap,like a turning on a garden house and one of the pintels in the number 4 injector was broken from his bad doing and caused number 4 piston to basically crack the length of it in two.All the fuel was washing oil off the bore,hence causing damage.Spray pattern is important.IM not sure on Rb25 injectors but these were on SR20det ones.

Highflowed R34 ones from the US....good option www.deatschwerks.com

they are awesome i had a set of them, they were flow tested a 600cc they were all with in 2cc of each other and gave me mo problems what so ever

they are awesome i had a set of them, they were flow tested a 600cc they were all with in 2cc of each other and gave me mo problems what so ever

I just had a look on the site and they look very professional. Are they new OEM injectors that they high flow, pressure test, etc, etc and resell? Is that how it works?

when i got my injectors cleaned i talked to the injector guy about highflows and he said he wouldn't ever touch them, he said he's seen some good ones but on the most part they we all crap different flow rates etc. Your motor your risk.

when i got my injectors cleaned i talked to the injector guy about highflows and he said he wouldn't ever touch them, he said he's seen some good ones but on the most part they we all crap different flow rates etc. Your motor your risk.

thats why when you get them you flow test them :laugh: like i said mine were all within 2cc, if you test them you cant go wrong

Hey hey,

I'm just looking for some names and numbers of people that highflow std R34 rb25 injectors in Brissie. What are some costs and options???

thanks guys,

Steve

why hi-flow std injectors.

you can buy some aftermarket injector for a bit more money than hi-flow std injectors.

much better way to do and brand new too

cheers

thats why when you get them you flow test them :D like i said mine were all within 2cc, if you test them you cant go wrong

Yep, they even have so many cores in stock, they flow test and match a group of 6 so the tolerance between them is very close. I've heard nothing but praise for Deatschwerks, my ones have been running great for a long time now.

They highflow the pintle exactly the same way a manufacturer would, using micron accurate drills an CNC.

yeah i nearly got a set of deathworks highflows as well but read more than a couple of bad reports of injectors failing, locking up on the dyno and sorts. But I suppose bad reports are everywhere for everything

Edited by SevenAngryPenguins
why hi-flow std injectors.

you can buy some aftermarket injector for a bit more money than hi-flow std injectors.

much better way to do and brand new too

cheers

because they are cheaper and made by the same process and are effectively new

Yep, they even have so many cores in stock, they flow test and match a group of 6 so the tolerance between them is very close. I've heard nothing but praise for Deatschwerks, my ones have been running great for a long time now.

They highflow the pintle exactly the same way a manufacturer would, using micron accurate drills an CNC.

dont tell any one else that though...cause when you mention anything besides nismo when it comes to injectors they are apparently shit

I just heard they have arrived at my house... why do work days always go for so long?

I grabbed the 600cc variation of them. they are so cheap for brand new, flow tested & matched, 600cc injectors that are a drop in straight fitment... That has to be as good or better than any aftermarket brand injector, right???

And they only cost $550!

:D

I just heard they have arrived at my house... why do work days always go for so long?

I grabbed the 600cc variation of them. they are so cheap for brand new, flow tested & matched, 600cc injectors that are a drop in straight fitment... That has to be as good or better than any aftermarket brand injector, right???

And they only cost $550!

:(

Don't forget to send your ones back for cash-back!......another $90in your pocket

Don't forget to send your ones back for cash-back!......another $90in your pocket

do they take stock ones off of any one? Or only current customers? i have like 3 sets of RB 25 ones and 2 sets of SR20 ones!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...