Jump to content
SAU Community

Recommended Posts

Hey all,

I have spoken to a few people about running 15'' Drag rims on my GT-R R32.....they have all said its a hard process to get the right offset! I have seen many drag GT-R's running 15'' rims so its not impossible...

Is there anyone out there that can help me out here? is it possible to order the Drag rims with the offset i require? saving me the hassle of trial and error? If anyone has been through the convertion i would love to hear what you gotta say :thumbsup:

I honestly dont know much about this subject as you can tell...I really need some help here!

Any ideas?

Link to comment
https://www.sau.com.au/forums/topic/215394-drag-15-rims-need-help-with-offset/
Share on other sites

As long as your are prepared to put on spacers there should be no probs. They are illegal however

R32 GTR is a +30offset if that helps

You should be able go stock R32 GTST rims with a spacer (if u want cheap)

As long as your are prepared to put on spacers there should be no probs. They are illegal however

R32 GTR is a +30offset if that helps

You should be able go stock R32 GTST rims with a spacer (if u want cheap)

Its for a Drag GT-R so wanna run the 15'' rims

others?

sorry for my inexperience on the subject of drag, but do the rims need to be anything special to be a drag rim? as in are they typically made different from a normal road or circuit wheel?

as far as getting some wheels, most decent jap wheel manufacturers would make a 15x8-10ish (not sure what tyre u intend on running) as far as offset goes, a +30 should be alright, depending on the size of the tyre u intend on running, id be slightly worried about the tie rod end for the HICAS at the rear and the clearance there with a bigger wheel/tyre. but the most important part is disk type, you need to make sure (especially for the front) that u get a high disk, this will clear the calipers. as far as disk diametre goes, well i think a 15" at the front would be pushing it, but if uve seen others get away with it on stock disks then should be fine, just make sure u order a high disk and it should clear ur calipers. the main issue with most 15" wheels is they are made for cars with pretty much always have tiny brakes, so they often are a low disk and dont have much caliper clearance.

Hey nisskid Does this mean if i buy a 15 ''drag rim that has a offset off between 0 and +10 all i have to do is run spacer plates to make it around +30?

about the brakes if i come across fitment problems i will run smaller brakes etc...

Hey nisskid Does this mean if i buy a 15 ''drag rim that has a offset off between 0 and +10 all i have to do is run spacer plates to make it around +30?

about the brakes if i come across fitment problems i will run smaller brakes etc...

nah, it actually works the other way, spacers will reduce your offset, for instance a +20 offset with a 30mm spacer will make the offset effectively -10 offset. theres a few types of spacers, theres floating (slip on) spacers which just sit over the studs, these are usually used for <10mm applications as it reduces the usable length of the stud. then theres a bolt on spacer, these are usually >20mm, this would be ur best bet, finding a high offset wheel is easy as piss, especially with a 15" wheel, so you could get say a +45 (common offset) wheel and put a 25mm bolt on spacer making it around +20, then at least you dont have to worry about disk type etc as u know there will be probably be at least around 40mm of brake clearance, which should be enough for GTR calipers.

What size slicks do you want to run? That will determine the width of the wheel and then the offset required. The only issue with 15" wheels might be the brake clearance. Some wheel manufacturers can overcome this with different dish designs.

  • 1 month later...
You need 5.5" backspace 15x8" with 26 or 28 x 11.5 x 15 Mickey Thompson Et Street

Rear gtr r32 brakes isn't problem but the front sure it is big problem with 15"! You must use front brakes from 180sx S13 with redrilled disks :wub:

f**k thats a scary thought lol

The owner have it for DRAG use!! :wub:

The brakes from s13 fits with only a redrill on the discs because s13 is 4x114.3 and skyline 5x114.3, there are two generations.. 280mm and 256mm both will fit in 15" wheels easy!! But maybe you will need s13 rear brakes too to keep the right brake bias! For drag use you will not have any problem!! :/ Also they are lighter ;)

  • 8 years later...

apologies on the dig up, saves me from posting the same question twice more or less...

I also too am in interested in running a set of drag rims on my R33 GTR , can anyone else she light on what size and backspace i'd need?

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
    • That's my life. Past-Duncan has a lot to answer for
×
×
  • Create New...