Jump to content
SAU Community

Recommended Posts

Hey guys I have a question about the power fc that i couldnt find an answer to.

I recently bought a second hand power fc and was told by the guy that had it that my car wouldnt run on it (he had monster turbo, cams, injectors etc).

So heres my dilema, If i reset the power fc, will it go back to the base map they are purcahsed with (fingures crossed)?

or will I have to find someone who has the map saved so I can download it?

The reason I am doing this is so I can check everything is ok before making the 6 hour drive to my nearest tuner. :D

Thanks for any help.

Link to comment
https://www.sau.com.au/forums/topic/215418-apexi-power-fc/
Share on other sites

yeah can reset it back to original settings no worries. SHould never run a tune from one car on another, no matter how similar or different the engine mods are. always start a tune frlom scratch.

you will be fine to reset it, plug it in, and drive to ur tuner. just make sure you follow the instructions. do a serch for power fc, paulr33 has done a hgell of a write up on them on here.

Link to comment
https://www.sau.com.au/forums/topic/215418-apexi-power-fc/#findComment-3805704
Share on other sites

Too easy, just bounce it and your away. Rem not to load the car up till tuned.

I know when i fitted mine, even before tunning it was a fair deal more responsive down low, as it had a lot more ignition then stock... which coulda been an issue if thrashed on a hot day, with bad fuel etc.

Link to comment
https://www.sau.com.au/forums/topic/215418-apexi-power-fc/#findComment-3808214
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...