Jump to content
SAU Community

Willl R34 Gtr Side Skirts Fit Onto A Gtt?

DNGRUS

By DNGRUS,
in Exterior & Interior Styling

 Share

Recommended Posts

Yo-Yo Grand Master

Yo-Yo

Posted
Posted (edited)

Hopefully this can help...

1st pic is a GT-t with the nismo add on side-lip that bolts onto the bottom, meant for a GTR so safe to assume GTR/T skirts are the same length...

Whether or not the flared guards of the GTR affect the bottom section where a normal skirt would attach is another question, maybe you can make it out in the pics or compare other

GT-R replica

post-29425-1209134236_thumb.jpg

Real Deal

post-29425-1209134248_thumb.jpg

Good luck! :)

Edited by Yo-Yo
candy33 Experienced

candy33

Posted
Posted

No they will not fit without modifications.

My brother tried doing it on his GTT and it seems that you have to bend the rear half of the skirts in as the gtt's have narrower gaurds.

Length is the same though, but as i remember there will be about an inch gap from the skirt to the rear gaurds and front guards.

But if the skirts are fibreglass its an easy fix, just chop off and reglass.

DECIM8 Grand Master

DECIM8

Posted
Posted

From what infomation I got the side skirts will fit, the wide body conversion I wanted to do only drops down to the side skirt and then you bolt on a gtr side skirt to match the wide body, perhaps that only works with fibreglass? I have no idea but thats what i was informed.

Just buy east bear kit ferah, all the crap bolting on oem is too hard.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...