Jump to content
SAU Community

Recommended Posts

As with our standard cruise rules, IMPORT/JAP CARS ONLY.

Saturday Night

17th May

Meet Point

Harvey Norman Mandurah

Time

meet 8pm depart 8:30pm

Heading up city way, NOT stopping through Rockingham. Regroup points will NOT be provided in this thread for this cruise. PM if you require this info.

I'll be riding shotgun in the black 180 getting some footage as my car won't be going to cruises for another month or so. :P

Edited by Magic
Link to comment
https://www.sau.com.au/forums/topic/216510-club-motavatecom-cruise-may-17th/
Share on other sites

Friday night

Meet point and times TBA

mark your calenders. :cheers:

Oks, i spose i'll come on this one lol. Course i'll come! Gotta support us skyline drivers. Those rex's are increasing in number lolz.

Catchya

  • 2 weeks later...

For NOR ppl, theres a meet at Perry Lakes drive, Floreat at the Floreat Sports grounds at about 10 - 10.30. I know its late notice but i've ony been told where a NOR meet point is.

Catchya

Good cruise as always guys. However I have been told a few skylines and FC's had some troubles with booze buses/cops.'

Let me know how you's went, pm or on here, up to you. :D

p.s I find it really 'convenient' when you pass a cop while doing nothing wrong, and they IMMEDIATELY decide to do do a u-turn and tailgait you no matter which turn you take.

They then eventually took hiding and came out, lured most into a booze bus location by more tailgaiting.

It was the most responsible cruise I've been on tbh. If find that quite ridiculous on the cops behalf, but thanks for those who represented. See you next month. :D

Edited by Magic

it was fun, despite getting singled out cuz i was at the front of the line - Mr Policeman was very nice. A bit surprised to find me behind the wheel but then we had a laugh about it. And I was allowed to go without a second glance at my car. Phew.

Yeah man did we drive past you and you did a u-turn? on one of the darker roads. I was in the black 180 about 5 cars in front of you I think. Also recognisable as the drunk guy sticking half his body out the window filming lol.

Yeah man did we drive past you and you did a u-turn? on one of the darker roads. I was in the black 180 about 5 cars in front of you I think. Also recognisable as the drunk guy sticking half his body out the window filming lol.

yeah it was pretty fun didnt even know it was on

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...