Jump to content
SAU Community

Jap Wreckers

ONYX

By ONYX,
in Western Australia

 Share

Recommended Posts

ONYX Grand Master

ONYX

Posted
Posted

Hey guys, cos im lazy, and i don't wanna look at the phone book, and cos i want your experiences,

i wanna know where there are jap wreckers in perth, and your personal experiences with them

the only 1 i can think of off the top of my head is in welshpool near where i used to work, on Pilbara st i think... not to sure, don't remember what its called:rolleyes:

looking for a few little bits n pieces

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/
Share on other sites
SHUTO-BOY Grand Master

SHUTO-BOY

Posted
Posted

hey memphis, i need driver side door pillar thingy(between the driver mirror and the rear quarter mirror), mine got ripped off when some guy tried to break into my car (good thing i have metal sleeved tint)

hope u can ask them for me, my number is 0401290390,pls give me a sms

Aidwin

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-458597
Share on other sites
GTS500 Community Regular

GTS500

Posted
Posted

jap motor sport in sydney and just jap in adelaide are both very good and will post most things over including frieght cheaper than any company in perth could sell it to you.The only other person you mite want to try is Mayhem on this site as he sometimes brings in half cuts.hope this helps.

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-460573
Share on other sites
Milo Community Regular

Milo

Posted
Posted

In cannington there is japwreck and Nispart Datpart I am not sure of addresses. One is near bunnings, the other near the big WA salvage. For common older stuff Niss part but Japwreck have engines mirrors front cuts strut bars etc etc.

Actually the most helpful cos i needed some small plastic wiper box screws was pulsarwreck around the corner for nisspart.

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-461040
Share on other sites
  • 2 weeks later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Was that with the cas upside or correct way up?
    • nash47
      Cas issue

      By nash47 · Posted

      Did and sync timing with light 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
×
×
  • Create New...