Jump to content
SAU Community

Jap Wreckers

ONYX

By ONYX,
in Western Australia

 Share

Recommended Posts

ONYX Grand Master

ONYX

Posted
Posted

Hey guys, cos im lazy, and i don't wanna look at the phone book, and cos i want your experiences,

i wanna know where there are jap wreckers in perth, and your personal experiences with them

the only 1 i can think of off the top of my head is in welshpool near where i used to work, on Pilbara st i think... not to sure, don't remember what its called:rolleyes:

looking for a few little bits n pieces

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/
Share on other sites
SHUTO-BOY Grand Master

SHUTO-BOY

Posted
Posted

hey memphis, i need driver side door pillar thingy(between the driver mirror and the rear quarter mirror), mine got ripped off when some guy tried to break into my car (good thing i have metal sleeved tint)

hope u can ask them for me, my number is 0401290390,pls give me a sms

Aidwin

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-458597
Share on other sites
GTS500 Community Regular

GTS500

Posted
Posted

jap motor sport in sydney and just jap in adelaide are both very good and will post most things over including frieght cheaper than any company in perth could sell it to you.The only other person you mite want to try is Mayhem on this site as he sometimes brings in half cuts.hope this helps.

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-460573
Share on other sites
Milo Community Regular

Milo

Posted
Posted

In cannington there is japwreck and Nispart Datpart I am not sure of addresses. One is near bunnings, the other near the big WA salvage. For common older stuff Niss part but Japwreck have engines mirrors front cuts strut bars etc etc.

Actually the most helpful cos i needed some small plastic wiper box screws was pulsarwreck around the corner for nisspart.

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-461040
Share on other sites
  • 2 weeks later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      21 is explicitly the coils detected as the issue. Is it guaranteed the actual issue? No. Just the ECU thinks it is. When you say rattling, describe it better, get an audio clip as best you can if possible.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      Yea got me coppers. Bad news is I just put them in and the car still has the light and shakes. I also noticed I hear like rattling coming from the exhaust piping right under me. Does 21 also have a possibility of being O2 sensors?   So, coil packs are good, the harness is good, the MAF is working, and obviously the spark plugs just replaced and working.
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      Make sure you drop the GTT base tune back in, and set your injectors again, this will remove anything playing up with it you may have removed. Possibly lean there as it's normally a fast transient going THROUGH atmospheric pressure, and a turbo motor would then quickly go richer as boost builds. The only worry you MIGHT have is ignition timing, as the DE is higher compression than the DET from memory. But again, you're not in boost, so the DE motor will be a lot more forgiving at atmospheric.   Get Murray, Kinkstahs, and Johnny's input on tuning haltechs, those guys have played with tuning enough in the past to be able to help now you're past the trouble shooting stage of the MAP issue
    • albyz34gt
      HELP r34 n/a turbo conversation

      By albyz34gt · Posted

      @Rusty NutshI mate. Do you have a pinout diagram for the na neo auto ecu? 
    • Harinder singh
      Engine Issue

      By Harinder singh · Posted

      Yeah thats the plan now. 🤞
×
×
  • Create New...