Jump to content
SAU Community

Recommended Posts

Hey,

Was this car always manual or did you convert it when you did engine? How many k's has the box done? Has it always had short shifter on it?

Thanks,

Courtney

  • Replies 192
  • Created
  • Last Reply

Top Posters In This Topic

Hey,

Was this car always manual or did you convert it when you did engine? How many k's has the box done? Has it always had short shifter on it?

Thanks,

Courtney

always been manual. box has done 110k km. i bought the c's short shifter right after i bought the car. (short shifter has sold)

cheers,

Michael

hey mate where exactly are you located

and will the rear bar and skirts fit a series 2 r33 coupe?

any 1 no

cus if so if u still got ill take

also might be interested in the carpet if u still got it

and maybe the starter is the front windscreen ok?

if so wil it fit my car

cheers

ay mate after a few parts (quwations first)

Nismo 320 dash - $600 has never been used only taken out of the box once to check connections________will this work in my ecr33 1995 series 1.5 r33 gts25t?????

White skyline bit - $50 (is this the one that is clear in the back part just painted, ????,)

hit me up with a pm cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...