Jump to content
SAU Community

Recommended Posts

Clutch pedal gone all of a sudden whilst driving ...

Hey,

I was driving along yesterday and went to change from 2nd to 3rd when the clutch pedal just seemed to fall to the floor. Now when I push the clutch pedal down it doesn't disengage the clutch properly. I have to push the pedal as hard as i can to get the car into gear and to get it home i had to blip the rev in between shift so that it wouldn't crunch gears. It's going to Bezerkly tomorrow to get checked out just wondering if anyone could give me an idea of whats going on cause its doing my head in...

Thanks :nyaanyaa:

Clutch pedal gone all of a sudden whilst driving ...

Hey,

I was driving along yesterday and went to change from 2nd to 3rd when the clutch pedal just seemed to fall to the floor. Now when I push the clutch pedal down it doesn't disengage the clutch properly. I have to push the pedal as hard as i can to get the car into gear and to get it home i had to blip the rev in between shift so that it wouldn't crunch gears. It's going to Bezerkly tomorrow to get checked out just wondering if anyone could give me an idea of whats going on cause its doing my head in...

Thanks :nyaanyaa:

most likely your clutch master cyl is gone

change the slave cyl as well if you're doing the master cylinder

check your clutch fluid level, if it's too low then top it up, pump the pedal up and drive it carefully to the mechanics to get it fixed

the genuine master and slave cylinders aren't that expensive from nissan, so just save yourself the hassle and get new ones instead of messing around trying to rebuild/reseal the master cyl.. if the master cyl bore is scored then u've wasted your time rebuilding it

I Wish I had an easy fix like that :(

Just Pulled my slave off to change as I thought it had gone only to find that the locating/pivot bolt for the clutch fork has snapped...Yay Gearbox has to come out now :)

speaking of spot welds on the pedal brackets..

this reminded me that few days ago when my friend's r33 got broken into when parked on the streets in redfern/waterloo area

nothing was stolen, all they did was they pulled the brackets out of the accelerator pedal

and punctured one rear tyre..

when i saw it i was surprised how it didnt seem too hard to pull the bracket out... done with just a bit of leverage, force wasnt even enough to bend the bracket

with clutch pedal being heavier than accelerator, especially if you have heavy duty clutch, i guess it'll become a weak point..

why would they pull the accelerator pedal box out?

that is quite random! :thumbsup:

ya it is

and popped one of the tyres too

the parking spots close to city, on the streets, in front of some houses..

they probably didnt like him parking there so decided to do something to his car so he won't park there

whoever did it knew skylines quite well by the way it was broken into...

I Wish I had an easy fix like that :P

Just Pulled my slave off to change as I thought it had gone only to find that the locating/pivot bolt for the clutch fork has snapped...Yay Gearbox has to come out now :D

Same thing happened to my friend last weekend at DECA in Shepparton, had to drive it back to melbourne with no clutch starting it in gear. Do you know if there's anything that gets left inside the box that could be left dangling and doing damage to the inside of the gearbox?? Sorry don't mean to hijack thread..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
×
×
  • Create New...