Jump to content
SAU Community

Recommended Posts

Head $SOLD

Short Motor $280 Perfect working order when removed

Coil packs (awesome Condition) with loom $100

Stock turbo Manifold $40

Stock cooler pipes $50

Aircon $120

Powersteering pump $120

R32 RB25DE NA Loom $100? Offers

R32 RB25DE NA Computer $100

R33 RB25DET Computer $140

Carbon Canister $20

Near New Genuine Nissan Water Pump $40

Brand new Genuine Nissan Timing belt $90

Cross over pipe $40

RB30 Sump $120 (basically same as RB25)

Probably got a few more parts I have forgotten will add later once I go have a search through

Link to comment
https://www.sau.com.au/forums/topic/218156-rb25det-parts/
Share on other sites

  • 2 weeks later...
is it a DET motor?

if so interested in the bottom end, as long as its not farked :blink:

not farked! Your welcome to come have a look!

did the rocker covers go with the head as well?

Sorry mate they did

Link to comment
https://www.sau.com.au/forums/topic/218156-rb25det-parts/#findComment-3873500
Share on other sites

heya mate

drop me a Pm with a phone numebr.

pretty keen on that bottom end, and if i dont grab it, one of my mates might when we determine whethe his motors done a bottom end bearing,

cheers daniel

Link to comment
https://www.sau.com.au/forums/topic/218156-rb25det-parts/#findComment-3874545
Share on other sites

heya mate

drop me a Pm with a phone numebr.

pretty keen on that bottom end, and if i dont grab it, one of my mates might when we determine whethe his motors done a bottom end bearing,

cheers daniel

PM Sent

Yeah could be keen on bottom end, we'll see how f**ked mine is when we tear it apart.

No worries

Hey mate, interested in the bottom end. Got any compression or leak down tests done before it was taken apart?

Sorry didnt get a chance :)

Hey Mate,

Was wondering if you still have the metal cooling pipe that comes from the turbo and follows up to the back of the engine.

It's a small thin metal pipe.

Cheers.

Gone - went with the turbs!

Link to comment
https://www.sau.com.au/forums/topic/218156-rb25det-parts/#findComment-3879537
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...