Jump to content
SAU Community

Recommended Posts

Hey Mofo's

I am organising to have another go of getting some Lines out at Test and Tune on the 21st of May, after the disappointment last time.

I am aware there were a fair few that couldn't attend for the last time for mods getting done or unexpected things that happened.

This time im looking for a low 12, and hope to see more then two skylines this time.

GET UR ASS'ES OUT THERE WHHOOPP WHHOOPP!!

How good is Johnny! keep Walking.

Link to comment
https://www.sau.com.au/forums/topic/218509-test-and-tune-21st-may-pu-pu-pu/
Share on other sites

Hey Mofo's

I am organising to have another go of getting some Lines out at Test and Tune on the 21st of May, after the disappointment last time.

I am aware there were a fair few that couldn't attend for the last time for mods getting done or unexpected things that happened.

This time im looking for a low 12, and hope to see more then two skylines this time.

GET UR ASS'ES OUT THERE WHHOOPP WHHOOPP!!

How good is Johnny! keep Walking.

hey this kellie i am all new to this site were are you holding this test and tune

Sweet as, looking forward to seein ya out there Brad.

(Also i will probably have some dosh for the rods if you could bring a set with ya on the night, if thats possible)

Paul- Will probably do the same as last time meet ya at mobil, but will ring ya when it gets closer to the date.

Col - i'll do it again, till we get everyone out on the one night. haha. (Hopefully the next couple of ones after this one i will have my forged motor in.)

Thanks again for the MT's , i had them on 22psi last time but should of ran them lower. Will try 15psi this time.

Hey guys

Ran a new PB last night, which i am fairly happy with cause i know i can still improve on teh time even more.

[email protected], 60FT 1.776. Mt Streets on roughly 18-19psi in the tyres. (was going to go lower but some reason i didn't.)

3rd gear i left it to rev out longer then i should of, and my launch i still believe i can work on.

Hopefully next time i will be a bees dick away from the 11's, Woohoo!! haha

I saw a couple of lines out there last night, whoever was out there let us know who you are on here.

Baz - well u know my story. The old infamous too much oil in the head. I need to put a drain in the back of the head to the sump, and I might go a bit smaller in my restrictors as well. Good excuse to get the engine out and HPC coat everything.

But Im hooked now - will be out again as soon as I fix.

That Silver R33 GTR did a 10.99 while I was there

Baz - well u know my story. The old infamous too much oil in the head. I need to put a drain in the back of the head to the sump, and I might go a bit smaller in my restrictors as well. Good excuse to get the engine out and HPC coat everything.

But Im hooked now - will be out again as soon as I fix.

That Silver R33 GTR did a 10.99 while I was there

yeah, bit unfortunate that it happened. Least its easy fix and wasn't anything too major ( well time consuming i guess you would call it), but yeah let us know once everything is back up and running and i'll organise to go down again.

Hopefully close to next time i will be fairly close to having my engine put together, and winde the boost up a bit more.

Also saw a silver r33 lag weapon that was interesting to watch. It was like "Launch, nothing, nothing, nothing, then BANG full boost!! haha loved it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...