Jump to content
SAU Community

Recommended Posts

Hey guys, little while ago there was a post where someone sourced some oil filter with the nut welded on top of the filter. Tried searching for it but couldn't find the post. Anyone know anything about them or been using it? Just curious cus i've runned out of oem oil filters and wanna to give them a go. Thinking would make it easier as i don't have a relocation kit.

Link to comment
https://www.sau.com.au/forums/topic/218678-oil-filter-with-nut-on-top/
Share on other sites

autobarn sell a 'drift' branded oil filter with nut on it.. its blue! cost 20 odd busk though ouch :)
You're on to it mate, that's the one URAS is recommending,hey what's $20 bucks for the features this filter has especially the ease of getting it off.

I would still recommend screwing these filters on by hand as normal if you can,and only using the nut for removal as if you use a spanner to do them up they will get powerful tight,you know when you put on a fresh filter and tighten it up that you can back it off easily if you want to straight away, but try it in a week and you know how hard they get,just my 2c worth Cheers Grey Pearl.

If a filter is done up to the right torque settings, you shouldn't need tools to remove it.

Every single car I have purchased in the last 5 yrs has had some spanner in the workshop try to tighten the neck of the friggin filter, resulting in squashing and possible damage to the rubber seal, and making it damn near impossible to get the filter off after the heat has helped it to stick.

All cars (including my GTR) had a screwdriver help me to convince the filter to let go and give up, but after that, hand tight has been more than enough to make a strong seal with the filter and make it possible to get off by hand only.

B.

My hand and filter removal tool doesnt fit down there in a bnr32 :P

yeah exactly my problem

I believe this is the topic you are refering to

http://www.skylinesaustralia.com/forums/Sw...bl-t204892.html

That's the one, thanks for that cooper. Looks like it hasn't been updated. Has anyone been using these?

You do them up about hand tight, but dont use anything else to do them up. I have heard stories of engines who have been destroyed because the oil filter was over tightened, something broke off and blocked off the flow. Do it as tight as you can by hand, but you will need a tool to get it off. If it is loose, it will leak oil

LoL at some of the suggestions.

Filter removal tools are just that.. for removal; u never use a tool to tighten a filter.

Remove filter, clean o-ring seat, lubricate new filters o-ring, tight by hand with moderate amount of force - done.

there are some orange filters out there that have the end you grip designed with a grip like paint on them to help you remove them ;)

Your talking about the Fram Grip, I think.

gallery_14713_1542_24561.jpg

In that famous oil filtration test done years ago, Fram didn't come up that well considering the cost.

Edited by GeeTR

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...