Jump to content
SAU Community

Recommended Posts

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

OK guys had a suggestion to change the location to Sunnybank Coffee Club this is where the Kmart and the AMC cinimas are located near the small roundabout if anyone has problems getting there feel free to contact me on my mobile listed above

It's Sunnybank Plaza Coffee Club. (Near to Maccas) :thumbsup:

My mates will be coming too.. but we will be late as usual.. :)

sooooo.... here?

Yeh that's the one mate :D The coffee club at the shopping complex is not inside the centre itself, it runs along the outside, it is straight across from the National Bank. Which is straight across from the Maccas :( There's a Fun House inside the centre so I think i'll be there before 7pm for some arcade gaming hehe

awsome nite guys thanks to everyone who turned up !! Special thanks to Andy and Anna for giving me a Jump Start !, and Adam for the Lift :)

Although Adam had to shit all the cinimon out of his ass towards the end of the nite !..

Sorry bud i wasnt driving adam was a bit too excited to keep on driving lol...

P.S glen/mick we have a new story for you guys Adams Maccers Toilet dilema !

Good meet last night. Company and conversations were good value. Next meet should be back at mt gravatt. Anna & JK, get a room. haha. Pitty you guys didn't go the cruise down to west end. Not much of a cruise after west end, got seperated at sth bank.

Col - I was wondering what the hell you were eating. That green crap didn't do it any favours, visually. haha.

Good meet last night. Company and conversations were good value. Next meet should be back at mt gravatt. Anna & JK, get a room. haha. Pitty you guys didn't go the cruise down to west end. Not much of a cruise after west end, got seperated at sth bank.

Col - I was wondering what the hell you were eating. That green crap didn't do it any favours, visually. haha.

but sunny bank has sushi next door :happy:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...