Jump to content
SAU Community

Recommended Posts

Item: Tomei Reytek programable ECU with map sensor

Age: 1-2 yrs

Condition: Perfect

Price: $800 ono

To Fit: (What car) R32 GTR

Location: Brisbane

Contact: PM or 0422382292

Comments:

This is a fully programable ECU which uses a map sensor to eliminate afm's like the D-jetro PFC. Im basically selling it as I couldnt find anyone at the time to tune it in Brisbane. I know that Unique Autosports in NSW sell and tune them, and some DR Drift (cant remember name)in Vic and a place in perth but could be more that do now. You can buy the tuning software and iterface kit from tomei for them too.

I pulled it out of my car which had it installed in the Tomei workshop in Japan along with other things. The car was running around 310awkw (mercury motorsports dyno)with T04R turbo (17psi), tomei 260 cams, upgraded pump and still with standard injectors. Car ran 11.5@126mph with that setup and was getting 500kms per tank of fuel. I have since upgraded many things and swapped for a PFC d-jetro cos no one tunes it in Brissie otherwise I would have kept it!

Unique autosports sell them for $1900 exchange---> http://www.uniqueautosports.com/ (look in the tomei section)

for more info ----> http://www.tomei-p.co.jp/_2003web-catalogu...dex-reytec.html

OTHER THINGS FOR SALE:

One set of R32 GTR injectors with fuel rail and nismo adjustable regulator. Was running 310awkw safely which led me to believe they might be highflowed but not sure?? Might need new buckets which can be bought from an injector place for a few dollars or less. Were running fine and pulled off for bigger items.

$400 for the lot. Will not separate

One GReddy 60mm black face mechanical boost guage. In perfect condition and working fine. Was in car when bought a replaced for a Defi guage. Just needs vacuum line to work.

$100

Chrome catch can which I bought a while ago. Still new in box with all parts required.

$30

RB26 cam gear front cover and stock cam gears in good condition

$75

RB26 oil breather U pipe between cam covers in perfect condition

$20

RB26 clutch pack fan. Was in good working order and not slipping. I have grinded a little off the edge off the blades as seen in pics to clear the radiator I put in. I went to thermos as the shroud couldnt be used. The grinding hasnt done anything to performance of fan.

$30

If interested either reply, PM or call me on 0422382292. Will post interstate at buyers cost. Prices are neg.

Cheers,

Glenn

post-4200-1210563831_thumb.jpg

post-4200-1210563848_thumb.jpg

post-4200-1210563876_thumb.jpg

post-4200-1210563896_thumb.jpg

post-4200-1210563915_thumb.jpg

post-4200-1210564074_thumb.jpg

post-4200-1210564167_thumb.jpg

post-4200-1210564263_thumb.jpg

post-4200-1210564337_thumb.jpg

Edited by 06tst

price drop on Tomei Reytek ---> $700 ono. I need this gone asap!

It is a great ecu and fully tunable. If you are in Sydney and looking for a cheaper option programable ECU this is it. Unique Autosports deal with them in the western suburbs (seven hills) of sydney and can tune them.

Also Melbourne people, DR DRIFT can tune them aswell. He is also in western suburbs at Brooklyn.

price drop on Tomei Reytek ---> $700 ono. I need this gone asap!

It is a great ecu and fully tunable. If you are in Sydney and looking for a cheaper option programable ECU this is it. Unique Autosports deal with them in the western suburbs (seven hills) of sydney and can tune them.

Also Melbourne people, DR DRIFT can tune them aswell. He is also in western suburbs at Brooklyn.

i can tune thenm also, whats your best price?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Slow when hot could also be because its getting more dynamic compression, OR things are getting a bit tighter once it is all expanded. If it were an earthing issue, typically I'd expect you to have it have issues all the time. Unless it's really a combination of both things. Where the higher compression, and things being a bit tighter, is giving that bit of extra load and you do need a slight clean up on the cables/connections.
    • Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
×
×
  • Create New...