Jump to content
SAU Community

Recommended Posts

don't listen to him..

yes you can replace with just one.

you'll need to make some sort of adapter up though.

I'll buy your shitty stock ones for $50.

that should be enough to have a custom, shiny metal adapter plate for your single atmo bov.

I would imagine just fitting one and blocking the other off as if you wanted to do the flutter it would work. I haven't actually seen the piping of the GTR and thought about it to really say.

Edit: Just realised there was no point to this post. :P

Edited by adam-__-

You can do that no worries, but remember its one pipe going into two bov's. Not two pipes, so all the air will just be fed to the one bov. You usually put two on as a better attempt to vent all the air. Putting one atmo bov on will just make it work harder and possibly not vent enough air so the excess would be sent back to the turbo charger and you would experience the flutter noise.

thanks for the info guys. I dont want to change the bovs by choice its just that i have bought a hard pipe kit for my gtr and the pipeing kit does not have provisions for the bov's to be plumbed back so my standard bov's are venting to the atmosphere at the moment and i think this is why i have poor idel and boost response takes a little longer to come on

thanks for the info guys. I dont want to change the bovs by choice its just that i have bought a hard pipe kit for my gtr and the pipeing kit does not have provisions for the bov's to be plumbed back so my standard bov's are venting to the atmosphere at the moment and i think this is why i have poor idel and boost response takes a little longer to come on

Id say your problem is more likely attributed to the fact you're venting to atmo, not that your using stock BOV to do so.

IE stock or aftermarket, without a retune your still going to have the same problem

GTR stock BOV's are better in every way than almost every aftermarket BOV I have ever tried. It's a 99.9% guarantee that it won't matter what BOV you use, you will still have the same problem.

Cheers

Gary

if your car still uses AFM, then they have to be plumbed back in.

the factory ones do not stay shut at idle.

so essentially, you have an air leak.

un-metered air entering your engine.

a:f mixture is screwed and you get idle/stalling issues etc.

If you are still running air-flow meters, you need to plumb the BOVs back to make the car run properly. no ifs, no buts.

If you have MAP fuelling, feel free to go nuts with BOVs that vent to atmosphere.

there are people who have atmo venting bovs on AFM equipt GTR's with no problems.

but there is always some tuning to help it.

I'm not sure of the exact parameter that needs to be adjusted but it would have something to do with overrun fueling or throttle closed fueling or something that describes what the ecu does when throttle is shut.

basically, you want to remove fuel at that point so that when the atmo bov vents the air out of the system, then the ecu doesn't inject the fuel it was going to, that would have mixed with the air that was vented.

  • 4 weeks later...

My GTR came over with twin atmo Blitz BOVs, no major issues - just runs a lil rich between gear changes, but I would of kept the stockers if I had a chance.

btw the newer hks ssqv for gtr comes with the adapter/replacement pipe to suit single atmo bov.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...