Jump to content
SAU Community

Recommended Posts

Moving out all these parts as I'm selling my car and have no use for them anymore . All parts are quality and new or near new grab yourself a bargain . All items don't include postage pickup also available in Sydney .

Item: Greddy Plenum

Age: New

Condition:New

Price: $950

Location:Sydney

Contact: Private message or email [email protected]

Comments: Greddy Plenum brand new never used comes with everything as delivered from Greddy . Manifold has been smoothed and professionally painted in bright silver 2pac looks stunning .

parts007vz9.jpg

parts005kt0.jpg

Item : Q45 throttle body

Condition: used

Price: $200 Pending sale

Location :Sydney

Comments: Used q45 throttle body pefect match up for greddy plenum can work out negotiate package deal with plenum

parts006bg3.jpg

Item : Jim Berry Clutch full monty to suit r33 GTS-t and others

Condition : Brand new

Price: $1100

Comments : Orded from Jim few weeks ago this is exactly how I got the clutch kit from him . It's his signature full monty clutch to suit r33 GTS-t and also others .

parts001nl2.jpg

Item: Tomei Pon cams to suit RB25det

Condition : New

Price : $650

Comments : Tomei pon cams 256deg to suit rb25det brand new in the box as recieved from slide performance

parts003jz6.jpg

Item : Tomei Adjustable cam wheels

condition: New

Price: $280

Comments: Tomei Adjustable cam wheels to suit RB engines both wheels brand new in the box never used

parts004iv7.jpg

Item : Splitfire coil packs to suit r33 series2

Condition: used

Price: $400

Comments : Splitfire coil packs in original box to suit r33 series 2 . They haven't been run in the car but were just placed in the engine for a couple of days they are pretty much unused .

Edited by 7heavn

Where did you get the plenum painted? And how much did it cost you? Do you have a paint code for it?

Im sending my pressure plate to jim tomorrow.Will get it back all nice and upgraded with a 5 puk carbonic and sprung clutch plate.

This is a good price for this clutch,whoever buys it will be extremely happy.

Are the Poncams for RB25s up to 9/97 builds?

I'm a spray painter by trade I did the plenum myself it's a show quality finish I spent alot of hours getting it right The colour is straight 513B debber base coat silver with debber MS 2pac clear . Pon cams where to suit my 96 ser2 GTS-t.

I'm a spray painter by trade I did the plenum myself it's a show quality finish I spent alot of hours getting it right The colour is straight 513B debber base coat silver with debber MS 2pac clear . Pon cams where to suit my 96 ser2 GTS-t.

I assume you are in Sydney.How much would you charge to do the paint on my Greddy Plenum?

I assume you are in Sydney.How much would you charge to do the paint on my Greddy Plenum?

honestly just buy his then re-sell yours!

PS that plenum looks schmick!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...