Jump to content
SAU Community

Recommended Posts

As title says I have a set of 19" ROH drift R's to get rid off they are in good nick. There is one small mark on one of the rear rims and a mark on the inside of one of the fronts (I don't know how that got there :down: ). One of the rears is missing the R badge from the centre cap.

They have Hankook K104's on all four corners, both fronts have about 80-90% of the tread left and the rears have about 10% before they hit the wear indicators.

The rims are about 3-4 years old.

They measure 8.5 inches at the front and 9.5 at the rear. They were ordered with the offset to suit a R33 GTST, I can’t find the off set printed any where on the back of the rim. They fitted my car which has a wheel centre to guard height of 350mm and a camber kit on the front and rear, Both front and rear guards had to be rolled once the camber kits where installed.

I am located in the Hunter Valley N.S.W, feel free to PM me or post at will.

I am asking $1200.00 ono

:wub:

Ryan

post-14375-1210921164_thumb.jpg

post-14375-1210921232_thumb.jpg

post-14375-1210921263_thumb.jpg

post-14375-1210921302_thumb.jpg

post-14375-1210921453_thumb.jpg

post-14375-1210921483_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/219495-19-roh-drift-rs/
Share on other sites

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...