Jump to content
SAU Community

Recommended Posts

What brand;

Autometre ( are they accurate but? )

Spitfire ?

VDO

Actually I want one with a black background but with green dials and numbers. ? is it called ****pit vision or something?

What should I be paying for it and how much do they charge for install. Or is it easy and can u do it yourself ?

Thanks

Guest RedLineGTR

How much do you want to spend thats the thing...most people got for autometre ones they are cheaper and look better than the spitfire and VDO gauges. The Auotmeter ones are heaper than the jap brands but i personlly dont like the look of em i rather pay abit more and get jap one with some style some people are happy with the autometer ones, depends on your own personal choice. Cheers Rob

Depends on what your after.

I got a VDO boost and oil temp in mine cause I wanted the factory look.

Everyone said that the VDO boost gauges weren't very good, but when I had my car on the dyno the boost gauge was out by 0.2psi at 12psi (dyno read 12.2psi and boost gauge said 12psi) !!!

I think that is pretty good for the $125 that I paid ;)

J

Guest Boxhead

yes it comes down to how much you want to pay, i know my boost gauge is very accurate, on dyno it read 12.55 psi and gauge said just in between 12-13 psi...

im happy, it does the job, personally, i rekon its best to keep an eye out on the forums etc might get one cheap, or go to an import wreckers, they might have what your after... as i have asked one place, and he said they get them all the time, but just didnt have any atm coz there waiting for next container to arrive...

by the way i have an autometer

Do u think I should get an oil pressure one aswell, since I only have a stock one on the dash at the moment.

If I buy one, it might be more accurate than the dash one ?

my car is standard at the moment, do u think I would need an oil temp one or maybe a voltmetre might be handy.....I was thinkin about riggin them up under the stereo...

No pillar mounts as they are illegal so I heard

Swordfish, just for your reference, this is my din gauge setup..... a boost gauge is going in where the factory clock is and i'll be moving the climate control down the bottom and the gauges up to the top in a few weeks (wire lengths permitting - finger crossed!)

i've got a "swoosh" gauge that cost me $80 new, when tested on the dyno it read about 1psi more than the dyno gauge, works for me :(

Swordfish19792002: piller mounts r legal as long as there below the top of the steering wheel.

Guest Boxhead

not cheap at all... and also they are electrical, therefor you need controller which i have heard is around the 400 ish mark alone...

go the glovebox set up :( stealth, and when car is parked, no one will see gauges, and go, smash window rip them out...

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...