Jump to content
SAU Community

Second Water Pump Failier?

DjeMz

By DjeMz,
in Engines & Forced Induction

 Share

Recommended Posts

DjeMz Mentor

DjeMz

Posted
Posted

hey all

about a week ago my original water pump started leaking from the drainer hole thingy.

so i went off to the wreckers and bought a new one.

after the fkn hassel of taking off timing belt, harmonic balancer (took agesss to find the right HB puley remover) and all other other crap i finally changed the water pump...

put my new alim rad in, flushed the engine for 20 mins and all the rest of it, topped the coolant then SAME THING STARTED leaking!!

again, from the drainer hole.

my question is, was it just realllly bad luck to get a dogey water pump or is there something wrong?

if it is a dogey water pump, im definately going to buy a brand new one (if i knew it was going to be that much of a headache taking all that crap off i would have done it in the first place).

any help would be much appreciated!

thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/220291-second-water-pump-failier/
Share on other sites
DjeMz Mentor

DjeMz

Posted
  • Author
Posted

yeah sorry it was a second hand pump. its leaking from the drainer hole from the bottom of the pump (exact same place the old one was leaking from)

keep in mind it started leaking the day i installed it, didnt even get to drive the car :)

should i invest an extra $30 in a n1 pump, or will the 50mm aluminum rad be enough to keep the temps down?

abu Grand Master

abu

Posted
Posted
ohh true abu, i should just weld a 0.5mm tin sheet over where the pump should go yeah?

oh also i got aria forgies for my 13bt

:(

ah you wouldn't be in all this mess if you had a 20 like a true r32 owner

arias forgies suck, I went all out CP forgies with spool rods, extensive head work and solid lifters in my old 13BT

rb26s13 Mentor

rb26s13

Posted
Posted
ah you wouldn't be in all this mess if you had a 20 like a true r32 owner

arias forgies suck, I went all out CP forgies with spool rods, extensive head work and solid lifters in my old 13BT

you should invest in some procrams and cams gears for that rotor! really get that thing revving! :D

IanB Veteran

IanB

Posted
Posted

Unless you have a problem with them, I work at repco, I put a brand new GMB water pump for a RB30 on my 26 and its fine. Handles anything I can throw at it. I run stock rad, 16 PSI and it runs cooler then the stock pump did.

It cost me very little. What it costs the public I dont know, shouldnt be too much. If it was over 150 bucks id be very surprised.

DjeMz Mentor

DjeMz

Posted
  • Author
Posted

question, if a mechanic works on ur car after they have been supplied with a part from a wrecker, and that part is faulty and the mechanic charges me extra for fitting/removing/fitting a new part, can i forward that invoice to the wrecker?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • GTSBoy
      Rear Sway Bar Busshings - Holden Astra TS (2002)

      By GTSBoy · Posted

      I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...