Jump to content
SAU Community

Recommended Posts

Howdy,

Have a variety of things happening, Firstly I have just completed a round trip the qld from sydney nice 2000km on the clock and picked up some nice go fast bits on the way thanks Darrin.

After the first 1000km ( I drove through the night) the tyres which are at least 30-50% tread are gone!!! I did notice during wet patches the back swinging around as if Hicas was playing up, acclerating out of this tail movement helped.

anyway Im off to get a wheel alignment (and new tyres) tommorow but wondering if the problem could be hicas and perhaps its time to do the old hicas lock bar trick?

I must add the front tyres have almost no wear from the trip. not visable anyway.

To add to the story, the drive back was shocking, at one stage it was basically ice skating on the road, not due to bald tyres but because I was fighting with hicas to stay the shit still.

Help is greatly appreciated.

Nathaniel

P.S Hicas light never comes on, but I did have it up on the hoist some time ago and noticed one bush or join cover broken open for hicas, was told not to worry as its just hicas...

Edited by DECIM8
Link to comment
https://www.sau.com.au/forums/topic/220452-rear-tyres-bald/
Share on other sites

stop doing burnouts. seriously. :)

also, hicas doesn't cause tyre wear. both tyres always move in the same direction. If you really are getting tyre wear that bad i would expect to see feathering on the tread as it is being worn away very quickly. Either it had a shoddy alignment, someone pulled it apart and put it back together without bothering to even align it by eye, or someone has drifted hell sik bro into a kerb and bent the rear suspension.

take it to a tyre shop and get it aligned. it'll be toed in or out, probably toe out if you are having instability issues. I doubt it's hicas.

Link to comment
https://www.sau.com.au/forums/topic/220452-rear-tyres-bald/#findComment-3890254
Share on other sites

Drifting, burnouts.. everyone who ever cruses with me knows im the last person to do these things, I cant even keep up with the people infront let alone spin my tyres or do hecktik handbrake park jobs (although it did look pretty good on starsky and hutch)

Yeah ive never had the rear act up like that but I think its really down to the wet road no tyres thing.

Seriously ive got more wear on the left side vrs right side and more camber wear on the inside left vrs right yet ride height is exactly the same. I didnt get to take her to the tyre people today but any advice on a particular place in sydney?

Link to comment
https://www.sau.com.au/forums/topic/220452-rear-tyres-bald/#findComment-3890430
Share on other sites

Don't go somewhere crappy Nat (not that you would). I got an alignment not long ago and they didn't even get the steering wheel straight!

A good suspension shop AND ask for an inspection (rather than just align and piss off type job). There might be something unhappy back there that's costing you plenty of rubber (no, i'm not being filthy).

And stop doing burnouts. Srsly.

Link to comment
https://www.sau.com.au/forums/topic/220452-rear-tyres-bald/#findComment-3891390
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
    • Hi, i’m converted my r34 4dr auto to manual but need help with gearbox wiring. There are bunch of wires no idea which one for speedo drive, neutral, reverse can anyone help me. IMG_6860.mov
×
×
  • Create New...