Jump to content
SAU Community

Recommended Posts

Hi guys not sure if i posted this up in the right place...

Need some help iv got a r33 gtst with a Apexi power FC computer if i was to replace it back with the stock computer

what will i need to do to my car to make it run right and also how much power will it loose I currently have (265rwph)...

Any info would be help thanks

Link to comment
https://www.sau.com.au/forums/topic/220521-computer-change-r33-gtst/
Share on other sites

Hey guys mods a as follows:

Front mount intercooler

T4 turbo not sure how big its rated at

straight through exhaust

Pod Filter

Dual stage TURBOSMART Boost controller with tornado switch in middle console

Driftf adjustable BOV

Fuel system and injectors stock...

Your car will lose signiicant power if the PFC is tuned for those modifications.

Also running the bigger turbo with stock management is a dangerous proposition unless you baby the car everywhere (dont go WOT or take the revves above about 3.5k) as you risk detonation and engine failure. If you put the stock turbo back on the car would run fine (if a little rich).

Why do you want to remove the PFC?

Thanks heaps guys for the quick repleys and help...

Not sure if im 100% gonna remove the Power fc but my brothers mate offered me $1200 for the computer and hand held controller but i'll probably just leave it the way it is cos i do love my car and dont have the money for any engine rebuild lol

Keep in mind if you can sell the PFC for 1200 and get a stock ecu thrown in you can get toshi (search the traders forum for 'toshi') to remap you standard ECU for around $400 which is a very good option. It will be fine for the mods you have (and as its very hard to detect you wont get defected for it) the only downside is the PFC will be better if you want to do many more power mods in the future (bigger turbo, AFM, injectors, etc).

likely the car will run like a bag of shit with the ATMO BOV.

260rwhp is only 190rwkw, which for a turbo like that is a pretty poor result.

I'd expect closer to 300rwhp at least, and 350rwhp with injectors/AFM

So you wouldnt loose much power right power, would be a bit rougher to drive however as tune could have cleaned it up a bit

likely the car will run like a bag of shit with the ATMO BOV.

260rwhp is only 190rwkw, which for a turbo like that is a pretty poor result.

I'd expect closer to 300rwhp at least, and 350rwhp with injectors/AFM

So you wouldnt loose much power right power, would be a bit rougher to drive however as tune could have cleaned it up a bit

I was told that was about the right amount off power for the car as the injectors and fuel setup a still stock...

Also the t4 turbo i have isnt much bigger then the stock turbo, I'm not sure myself im only going on what the previous owner told me.

Its not about right :)

You can take factory injectors to around 220-230rwkw. Every car is different. I made 220rwkw on stock 25 injectors years ago with a T04e, int gated rear.

If its not visibly much bigger than the factory one, then it probably isnt a T04.

Generally a T04 will come with the .7A/R Garrett Comp cover

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...