Jump to content
SAU Community

Recommended Posts

79 on 280ZX was EFI in Oz and if your looking at n/a, the best bits are N42, but the block has to be modified to front sump as all zeds are rear sump pans.

Don't be fooled, the old L28, makes good power if modified a bit.

A stock RB30E is rated at 114kW at the fly and an L28E is rated at about 103kW so there isn't heaps in it.

Link to comment
https://www.sau.com.au/forums/topic/220604-r30/#findComment-3895099
Share on other sites

79 on 280ZX was EFI in Oz and if your looking at n/a, the best bits are N42, but the block has to be modified to front sump as all zeds are rear sump pans.

Don't be fooled, the old L28, makes good power if modified a bit.

A stock RB30E is rated at 114kW at the fly and an L28E is rated at about 103kW so there isn't heaps in it.

will the sump off the L24 bolt onto the L28 block??

Link to comment
https://www.sau.com.au/forums/topic/220604-r30/#findComment-3895625
Share on other sites

RB bolts straight onto r30 crossmember wit RB mounts. no probs. hardest thing is gearbox mount.... then tailshaft....

This is true, but there is no clearance from the sump to the x-member. Thats what i had found in my case.

So you can do it this way, it does work, but no one will engineer it. So technically you will never be able to register that car.

Link to comment
https://www.sau.com.au/forums/topic/220604-r30/#findComment-3898487
Share on other sites

This is true, but there is no clearance from the sump to the x-member. Thats what i had found in my case.

So you can do it this way, it does work, but no one will engineer it. So technically you will never be able to register that car.

maybe... mine has ample clearance, it all comes down to the angle the motor sits on.. i cant c why it cannot be engineerd as there is no welding or modifications to the crossmember or the mounts..

ne way just got a blue slip wit rb25 numbers so to the untrained the motor came out in that car. true ?

Link to comment
https://www.sau.com.au/forums/topic/220604-r30/#findComment-3898649
Share on other sites

No Hi Horse this time ............................ just quoting FACT! but obviously it's not the answer you were looking for.

Before I answered you before I consulted an old business associate, he is a current RTA registered examination/inspection station and was an RTA examiner before that, so I guess he should know his stuff when it comes to NSW registration. They (RTA) have all the books for all the models and what is or isn't or was or wasn't fitted to the car, but, as I guess you know everything so do as you please.

JFYI, what happens when you have an accident & maybe injure or kill someone with your DODGY registered car and you are sewed for damages by the CTP insurance company??????? You would need millions behind you as any insurance would become null & void when they find your car is illegal.

But you know all the answers eh! and it will never happen to you? ha ha ha ha, go and grow up!

Link to comment
https://www.sau.com.au/forums/topic/220604-r30/#findComment-3900466
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...