Jump to content
SAU Community

Recommended Posts

So i have a weird situation with my rb25 engine...

I think i have rounded it down the engine rings or turbo failure, but then again ive been wrong before, symptoms are;

It blows oil smoke(yes it is 100% oil smoke) after about 2 mins of driving, no massive embarrassing plooms but enough to be embarrased driving in mild traffic. There is no oil in the intake piping at all near the compressor or intercooler. I have a catchcan with blocked off pcv valve to plenum..catch can is venting to atmo... so there is no oil going back into the intake.

After hardcore drives the catch can fills about 30mls, but that could be becuase i still have rb20 rocker covers??, although i do think the engine is a little tired..

The car itself cranks over perfect.. cold, hot whenever and idles great no smoke. It is only when the car warms does it blow smoke..the worst is when just taking off there a ploom then it seems to go away, then when its boosts its back again, and if i give it full boost hard i can see it on the backoff.

I personally think a rear seal is goone in the turbocharger and there seems to be a more than usual amount of shaft play(its a bush bearing highflow), as i think i can see small burring on the compressor fins, and is a bit shiny where its been ever so slightly rubbing. Thing is, ive only had this turbo rebult in the last 7 months...which sucks.

The thing that stumps me is the intake piping is clean, if it the bearing it gone it usually leaks both sides right??

helpy??

cheers

Raz

probably a combination of both, those factory turbo's last about as long as the time the engines due for a rebuild. give or take a few 1000 k's

it doesnt cost much to give a block a hone and face or the bearing's either, it's the turbo that is going to set you back.

if it is the turbo seal you have to remember the longer it is driven the more oil it is going to spill down the exhaust,

so it is a compounding factor that it will only smoke more as the oil builds up in the exhaust,

even after you have found and fixed the issue you may find the smoke is still there for a few days untill the oil is burnt out of the system

I wouldnt say a few days but yeah

I think i wrote in the post, but the turbo is only 7 months old, its a highflow bush bearing with steel wheels..still has warrenty, and will be the cheapest option for the time being..since its still under warrenty.

cheers guys

you cant just guess, you have to look at a few things to be certain!my has same problem,i changed turbos to a highflow,and the problem was still there,oil coming out the bleeder and oil in the intercooler pipes,find out it was the valve seals,in the process of building a strong rb30 bottom end with rb25 head!

ok dude. you need to see if there is any back and forth movement in the turbo. not up and down. very common to have highflows shit a thrust bearing if still using standard oil lines and banjo bolts.

30mls is nothing to write home about. the symptoms you are describing is valve stem seals or turbine oil seal.

just check the turbo again and let us know :down:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...