Jump to content
SAU Community

Removing turbo on R33: How to.

JimX

By JimX,
in General Maintenance

 Share

Recommended Posts

JimX Grand Master

JimX

Posted
Posted

A few weeks ago I had to figure out how to remove my turbo. Thanks to the help of people on here I managed to do it relatively painlessly. So I thought I would put up what I did on my car a few weeks ago in a brief how-to for anyone's that's interested in removing their own turbo.

I decided to put it in here instead of Forced Induction Performance because it doesn't really have anything to do with performance unless you're upgrading or something. I did it myself as a maintenance procedure to repair the wastegate so I think it should be here.

Some of you might notice that I had this up on the Overclockers motoring forum, but I decided to pull it out because that forum is too full of tards. (any other ocau'ers please note: this is not a slight against ocau at all, Agg is a good friend of mine).

I didn't do this exactly as listed, because I tried some things and found they were too difficult and so attempted to get in other ways (eg, at first I tried doing everything from the top through the engine bay). This is how I ended up doing everything as best as I can remember it (apoligies for omissions and errors, if you find any please let me know and I'll fix it up).

This all applies directly to an R33 Skyline with a turbo in the factory spot with the water cooling lines installed. I suspect most factory turbo cars would be similar, but make note of any obvious differences between your car and an R33 before going ahead.

Start

1. Put your car in a secure garage or other covered workspace where you can leave it for at least a few days (this is assuming you will be sending your turbo off for inspection/repair).

2. Put the car up onto some wheel stands or ramps, to give yourself easy access to under the car.

3. With the engine COLD or at most, MODERATELY WARM (you really don't wanna burn yourself), remove the intake piping from the front of the turbo and move it out of the way.

Actually I'll just stop right here for a moment. If you want to simply check your bearings for play, just do step 3 without jacking the car up. Once you have exposed the compressor wheel, spin it with your fingers. It should rotate freely without any stickiness.

Push it inwards and outwards to check for axial play, it shouldn't move at all. If it moves even slightly, it needs a rebuild or will need one soon. Move it side to side, it should move very slightly (maybe not at all if a ball bearing turbo, not sure). It should not touch the turbo housing.

4. Remove the wastegate actuator (it gets in the way when removing/replacing the turbo). It's held in place with 2 mounting bolts and a spring clip on the wastegate pivot. The actuator is a round thing with a rod coming out the back. My car has an electronic boost controller which has a vacuum line up to the actuator which also needs to be removed. I'm not sure what cars without EBC's have to control the boost.

5. Put a large drip tray underneath the general area of the turbo. This is for catching coolant only, you won't lose very much oil at all on an R33. Some rags will take care of the small oil loss. The coolant will dribble down lots of places, so be prepared to shift the tray around for the best spot.

6. From the engine bay side, undo the oil and coolant line bolts. The oil line is small small bolts holding a metal jacket onto the top of the turbo, the coolant bolt is large and holds a round coolant terminal onto the side. There are brass washers that you need to be mindful of on the coolant lines, they are very easy to let drop onto the ground. One washer goes either side of the round coolant terminal for when you replace them.

7. From the underside of the car, undo the bolts for the same lines on the other side. The coolant line is on the engine block side, the oil line is underneath. I found the best position to reach was from behind the front crossmember.

8. Move the lines out of the way as best you can, being careful not to pinch or bend the metal.

9. Undo the 4 bolts holding the turbo onto the dump pipe (exhaust). Be careful not to lose the nuts, washers, and gaskets. Especially be wary of something falling down the exhaust, you really don't want to have to fish it out again!

10. Undo the 4 bolts holding the turbo's exhaust housing onto the exhaust manifold of the engine. Be careful not to lose gaskets, nuts, etc.

11. Carefully pull the turbo off and up out of the engine bay. You have to wriggle it around lots, to get it off both the exhaust and manifold, because there are 2 sets of studs on each keeping it in place.

12. If you need the wastegate actuator inspected/repaired as well as your turbo, now is a good time to put it back on.

Link to comment
https://www.sau.com.au/forums/topic/22118-removing-turbo-on-r33-how-to/
Share on other sites
  • 4 weeks later...
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      r34 Skyline 25 Gt four GTR conversion (ENR34)

      By GTSBoy · Posted

      Greg speaks wisdom. These dirty old Datsuns are only value when they are cheap. When they are not cheap, there is no value. Sounds contradictory, but it's true. We are now 20 years past the hey day of modifying cheap 90s JDM cars for small amounts of money. This is a different world. If you are rich and can afford not to care about what is effectively wasting money on an old Datto shitter, then I have no reason to argue against it. But if you are wanting to experience what we all experienced back in 2005 (and I bought my car last century!) then there is no way to do it.
    • Kinkstaah
      r34 Skyline 25 Gt four GTR conversion (ENR34)

      By Kinkstaah · Posted

      Short answer: No. Medium answer: No, because you still need to conjure the things out of thin air to bolt them to a NA to make it a NA+T. Long Answer: No - The things you need to conjure - meaning a turbo, intercooling, manifolds, exhaust, intake/manifold/piping, clutch, injectors, fuel pump, AFM (?), ECU + Wiring (woo, N/A loom fun) have to come from somewhere. You could have many scavenged these things from an OEM car that someone had upgraded from and use some of these. This will be cost prohibitive now, especially so in the USA. You'd probably pay the same for newer, upgraded components that are better than old OEM stuff from 25-30 years ago. None of these big ticket items are re-usable for the N/A car. Why not buy new and upgrade while you're there? The only real consideration is turbo and fuel sizing and determining whether you want to stay within the bounds of the OEM engine or get into rebuild territory. These limits ARE lower with a N/A motor and especially N/A gearbox at the starting point. And if you're gonna upgrade those then you may as well consider having them built to begin with. Because everyone here knows you're never far from that next engine rebuild once you start making the power you want... The cars you see on the internet and SAU etc have been built over decades. If you're really clued in... you would sell your US car to somebody for what you paid for it. You would then scour AU JDM pages or SAU and buy a car like Dose's on this forum with your powerful American Dollar. This will save you so much money in the long term. Importing it could be tricky. Or it might not because USA. I have long said the only reason 90's Japanese stuff took off was because a) Japanese people had Japanese cars so that is what they used b) Australians could import these cars to Australia with very minimal changes and use them on the road here c) Neither country had well-priced access to US or EU Sports Cars. I don't believe the JDM scene would have taken off in Australia at all if we had EU priced EU BMW M offerings, or more especially the AUS V8 Scene would never have existed if we had the multitude of US cars like Camaros, Mustangs, Corvettes at the prices you folks do. After all - Do the math. I would say put a V8 in your R34 and that's the smart way forward. It is. I did it. I know this from my own experience. But at that point there's no reason to simply not buy a C5 or C6? It would be simpler and easier and cheaper and bette-
    • AdiR34
      r34 Skyline 25 Gt four GTR conversion (ENR34)

      By AdiR34 · Posted

      Reading all this... hurts lol. I have an ENR34 5MT and I paid an inflated USA price for the car alone, had to do tons of preventative maintenance past that, and so I'm over $30K USD into the car already and haven't even touched power.  I wanted to +t it. Not even trying to make GTR numbers, I'd be happy with 250hp.  Can I get away with paying much less to make that happen?
    • Milkmun
      The Evolution Of "night Fury"

      By Milkmun · Posted

      Damn you’ve done well, definitely snapping necks.
    • acsplit
      SAU VIC Motorkhana Saturday 14th June Winton + Entry List & Accomodations details

      By acsplit · Posted

      Great weekend and event. Open fire at the caravan park, perfect weather all day and a great feed and a couple of drinks at at awesome country pub.
×
×
  • Create New...