Jump to content
SAU Community

Recommended Posts

Hi Guys.

Hopefully someone can point me in the right direction of solving such a seemingly insignificant problem.

Car: ECR33 GTS-T 186XXX km's, running 10PSI with bleed valve, Simota Pod filter, Gearbox Oil and Engine Oil + Filter changed less than 500kms ago.

When stepping on the pedal from idle lightly, the engine stutters roughly and then raises smoothly. The injectors tick/ tap like crazy and seem to have gotten louder in the last 1000kms and wasn't rectified when changing the oil? - if that matters at all.

When cold and gradually accelerating from 1000rpm to 3000rpm the car feels like it jutters forwards sometimes, like inconsistant power and is spasmodic in nature and minimal.

I don't have any experience with altering timing etc. but from what I have read I think this may have something to do with it. Also, the injectors are original and I have run Nulon fuel system/ injector cleaner through with a slight difference. Plugs have been cleaned and are not fouled up. Coil packs have been cleaned up and sealed using epoxy resin to cover cracks etc. with no misfire on boost :O I have cleaned the AAC valve and this has done nothing at all.

According to the previous owner, the O2 sensor in the dump pipe has been replaced - it doens't look like the original, although I am sure that the sensor in the cat has not been replaced.

Please help anyone! -

Link to comment
https://www.sau.com.au/forums/topic/221472-r33-rough-idle-and-stuttering/
Share on other sites

its a general skyline problem..

u'll get use to it..lol

but below are just some fix.....

try cleaning ur iacv..using some good carby cleaner/throttle body cleaner.....

that made alot of difference on most people skylines...

and also try cleaning ur afm out..using a good electrical cleaner....

other than that theres not much else you can do...

check ur spark-plugs...make sure there regapped to 0.8mm...

make sure u dont have any vac. leaks...

and have u got the standard blow-off valve?? atmo bov causes idle issues...

and last but not least get a tune...

hope this helps :ermm:

'bumble_bee' - Thankyou very much for the reply. I will check my bov - apparently it has been modified in some way and I will make sure I check the plugs as well - they are at 1.1mm. I will be getting a tune done too I think :ermm:

If anyone else can help, I would be greatly appreciative.

Thanks.

Edited by Ki_spirit

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I swear at my GKTech ones every time I have to take them apart and replace a spherical. But I wouldn't swap them for anything else. They absolutely slay every other option, at least in terms of how they actually work. You sure you don't want to live with bearings? I mean, they don't have "ball bearings". They are rod ends and sphericals throughout. Tough as nuts, even though I have found more than one way to wear them out.
    • From when I was looking at getting the 86 engineered for the turbo, the joint said to put in a few euro 5 or 6 cats, then tune the car on a nice clean E85 tune When I was looking at a turbo for the MX5, it was basically the same thing, a couple of cats and a nice clean tune Although, it will depend on the year of the Jeep IRT emmisions standards required, and what mods are done, especially if it has a newer engine installed that requires a higher Euro
    • Yeah - but it's not actually that easy. There are limits for HC, CO, NOx and particulates. Particulates shouldn't be a concern in any petrol engine unless trying to comply to the very latest Euro standard. But getting a tune right so that all the others stay within limits AT THE SAME TIME is not a trivial exercise. You couldn't possibly get it right by just guessing at the tuner's dyno, unless he had a 4 gas analyser up the pipe, which is not often the case these days. It used to be. Every decent shop that did "tune ups" (as opposed to tuning) would have a 4 gas analsyer. Perhaps there's still quite a few of them around these days. But most "tuners" are only watching O2 and power readings.
    • Slight segway but the most expensive part of the whole thing which I would have thought would only be required for an engine size/type swap, not a VIV test, is emissions testing.  That's when you get into the big bucks.  I can't remember the exact price now but I got quotes for the GT-R based on swapping to RB30 (not that anyone bothers doing it legally anymore...) and it was around $4500 just for that alone.  The guy that does them manipulates the tune on the vehicle to make sure it passes.  The cheaper option is to book into Kangan Batman Tafe (I think that's where it was) and hire their tester.  Allegedly you're not allowed in there with the car though so not in a position to tweak anything to make sure the vehicle passes.  I'm sure in this day and age of ultra tuneable ECU's you could get the tuner to program a special efficiency (clean) tune that emits the lowest amount of particulates possible that would pass the test.  It might only make 50kW's but as long as it passed who cares!
    • I'm sure he has left signs, or, he is looking down, laughing That's my cunning plan for when I leave, lots of half finished projects, with no rhyme or reason of where I was actually up to, just to keep everyone on their toes
×
×
  • Create New...