Jump to content
SAU Community

Recommended Posts

just wondering if anyone can help me with a problem with my rs4 s stagea?

it's surging while driving.

i already done coil packs . changed to splitfire.

using boash double platniums with gap 1.0mm. splitfire coils should jump that gap easy. no mod's only panel filter

i'm thinking air flow meter?

it seems to drive ok when cold but then if it hit a bump it starts to surg? and once it gets warm

but saying all that it comes and go's.

i also read that the soldering joints can break inside air flow meter. which would explan why it comes and go's

thanks ant :blink:

Link to comment
https://www.sau.com.au/forums/topic/221850-stagea-surging/
Share on other sites

It might just be a stagea thing, mine is similar. basically the ECU has much lower threshold for change than the equivalent 33 gtst one even on the same motor. mine started surging with only a unifilter panel filter and radiator air guide, and got much worse once i fitted a turbo back exhaust. the ecu sees an unusal voltage from the AFM for the load it is seeing and goes very rich, and retards the timing.

I fixed it temporarily using a HKS fuel cut defender, but am about to change the ECU to sort it properly long term. check out the stagea section lots of people have had similar problems

Link to comment
https://www.sau.com.au/forums/topic/221850-stagea-surging/#findComment-3910491
Share on other sites

It might just be a stagea thing, mine is similar. basically the ECU has much lower threshold for change than the equivalent 33 gtst one even on the same motor. mine started surging with only a unifilter panel filter and radiator air guide, and got much worse once i fitted a turbo back exhaust. the ecu sees an unusal voltage from the AFM for the load it is seeing and goes very rich, and retards the timing.

I fixed it temporarily using a HKS fuel cut defender, but am about to change the ECU to sort it properly long term. check out the stagea section lots of people have had similar problems

Thanks heaps Duncan.

Every bit of info helps. I noticed it was doing the same thing even when it was stock with standard air filter, cars only done 58000kms and it looks genuine.

I,ve done a few tests cheked fuel flow at 3000 rpm and it was 2.1 litres per minute, mixtures seem to be a bit lean at light throttle but ok at full throttle.

I've removed and cleaned air flow meter (not keen on pulling it apart until i've got another one to test with, but my mate has one I can test with so will do that on the weekend) if it still does same thing then I think you might be right about the ECU.

If that's the case Ill get a HKS fuel cut defender or source another ECU as you suggest.

Would the R33 gtst ECU be the same as the Stagea, also my Stagea is a manual so obviously I would have to go for a manual computer but I have heard that you can use Auto ECUs on manual cars, mine is the RB25 Neo motor. Is there any other ECUs that will do the job??

Another mate of mine also suggested throttle position sensor can also cause same problem, but if it was the throttle position sensor I would have thought it would have only done it on light throttle not through to full throttle??

But now that you say that it richens the mixture that makes sense to me as when I first got the car I was getting 550 km per tank and even 600km out on the open highway. Now I'm getting around 480km per tank and it seems to be doing it worse now than when I first got the car.

I'm at a bit of a loss, but I think I will just have to use the process of elimination.

If you can think of anything else that it might be please let me know.

Cheers :D

Link to comment
https://www.sau.com.au/forums/topic/221850-stagea-surging/#findComment-3915149
Share on other sites

  • 4 weeks later...
It might just be a stagea thing, mine is similar. basically the ECU has much lower threshold for change than the equivalent 33 gtst one even on the same motor. mine started surging with only a unifilter panel filter and radiator air guide, and got much worse once i fitted a turbo back exhaust. the ecu sees an unusal voltage from the AFM for the load it is seeing and goes very rich, and retards the timing.

I fixed it temporarily using a HKS fuel cut defender, but am about to change the ECU to sort it properly long term. check out the stagea section lots of people have had similar problems

Gday Duncan.

just thought I would let you know what that surging problem was, turned out to be tyre size. even though both front and back were both 235/ 45/ 17.

They were a different brand and the rolling diameter was different only by 35mm.

This was throwing the 4wd system out causing the surging/hesitation/shudder.

If you know anyone with a surge/hesitation/shudder problem with there stagea, r33 or r34 check this first and also the 4wd oil reservoir located in back of wagon on right hand side, must be checked after a drive, because when cold it will show an increased amount.

Link to comment
https://www.sau.com.au/forums/topic/221850-stagea-surging/#findComment-3992804
Share on other sites

if you are in sydney and want to try another standard RS4S ECU i have one lying around.

G'day Wolverine.

Thanks for your generous offer but just thought I would let you know I found out what that surging problem was, turned out to be tyre size even though both front and back were both 235/ 45/ 17 they were a different brand and the rolling diameter was different by 35mm. This was throwing the 4wd system out causing the surging/hesitation/shudder.

If you know anyone with a surge/hesitation/shudder problem with their stagea, r33 or r34 check this first and also the 4wd oil reservoir located in back of wagon on right hand side, must be checked after a drive, because when cold it will show an increased amount.

Link to comment
https://www.sau.com.au/forums/topic/221850-stagea-surging/#findComment-3992808
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
×
×
  • Create New...