Jump to content
SAU Community

Electrical Problem

partyboy73

By partyboy73,
in General Maintenance

 Share

Recommended Posts

partyboy73 Rising Star

partyboy73

Posted
Posted

This is a bit of a strange one so curious to see if anyone can work it out... Firstly one of my brake lights blew so as you do I changed it.. this is when things got strange cos after that I noticed that the left two lights were brighter than the right two, but when I pushed the brake pedal they swapped so the right ones were brighter and the left lighter... Then one of my reverse lights blew and since then all four of my rear lights have been as bright as if I was riding my brakes and when I do put the brakes on they only get brighter by the smallest amount... This senario was the most consistent and so I have not worried about it until I got pulled up and told to get it sorted. Does anyone have the slightest idea what is going on?

Link to comment
https://www.sau.com.au/forums/topic/221883-electrical-problem/
Share on other sites
partyboy73 Rising Star

partyboy73

Posted
  • Author
Posted (edited)
Have you replaced the blown reverse globe? Sounds like a crossed circuit.

No, I'm worried that if I replace it then some other weirder, worse thing will happen... How would I go about checking for a crossed circuit?

Edited by partyboy73

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      R34 GTR Front Diffuser/Guard Liner questions.

      By Kinkstaah · Posted

      Hello everyone. I've recently started the research into R34 GTR front bits and running into eye watering prices. On the plus site it looks like some places make 'replacement' fender liners for these cars. At eye-watering-but-less than stock prices. I also noticed there's plenty of diffuser options available too. What I would like to know is if my following assumptions are correct. 1) The OEM guard liners are actually only 'half' the liner. They go together with the OEM brake vents which are a separate item which looks to be quite a large 'panel' that is part of the liner. The GTR bumper has bolt holes along the front. I assume the ones in the vent correspond to the ones the OEM liner does not have (circled?)   2) The V-Spec front diffuser supplants the brake ducts in the above item. I am assuming these still work with the guard liners as there's no alternate part. I don't see how they go together, so I'm making the assumption that they do. I know the center splash guard is different on the V-Spec How does the liner interact with that? 3) There's alternate front diffusers that do away with it all. Annoyingly, a lot of the clones and CF different ones... have no brake ducts on them. I like the idea of them though. My brakes get hot on the track. These alternate diffusers are a lot cheaper than plastic splash guards. I'm assuming you don't have to/aren't supposed to remove guard liners to run a diffuser. I suspect that quite a few people actually do not run the guard liner because with a front undertray you're getting a lot of 'splash' guarding anyway, and most people remove liners given they're probably running a pretty aggressive setup with a diffuser at the front. It would also be nice to know if anyone has ever run the 'reproduction' guard liners and know whether the fitment is OEM quality or "OEM Quality". Example: https://www.ebay.com.au/itm/356254671561 https://carbonetics.net/products/nissan-skyline-r34-gtr-plastic-front-wheel-arch-set Is this knowledge still around?
    • MBS206
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By MBS206 · Posted

      Really, effort is pretty low. You hand fistfuls of cash over to someone else and pick it up when done...   And at least this shitbox isn't drinking coolant right?  
    • MBS206
      Cold compression test after rebuild... should I be worried?

      By MBS206 · Posted

      And most chargers that most DIY people own would put bugger all power back into the battery between cylinders. I've always done it with jumper packs/second battery connected. And that's on any car.   Because race car, and wanting the lightness.  At least in an R33, putting a bigger battery in can at least help shift the weight balance backwards  
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      OR, Tell the Motec to STFU, you said shift, so try shifting! But then yes, I agree, more sensors needed to. Put either a wheel speed sensor, or a diff speed sensor on it. Then get an input shaft speed sensor too. (I say input shaft speed, and not engine RPM). This way, you can now also log and see if the clutch is slipping (RPM, vs input shaft speed), and you can calculate gear (Input shaft speed / Output shaft speed). At least then if the gear position sensor fails you have a backup. And realistically, the Motec should only worry about what gear you're in for the parts where I'm assuming you have some power management strategies in it for the lower gears. (IE, lower boost, maybe different throttle curves, different ignition curves, etc etc). But it should stop it shifting. Pull the flappy, that f**ker should just attempt the motion! Heck, even on a sequential like on a motorbike, you can keep trying to kick it up a gear all you want, the physically part of the box takes care of not being able to loop the whole way around the box! Only part you'd have to worry is how it gets to reverse.  But that's on the driver... An R32 shouldn't be so smart as to try and override the driver on a gear shift  
    • GTSBoy
      Cold compression test after rebuild... should I be worried?

      By GTSBoy · Posted

      Yeah, nah. Anyone not putting the absolutely largest battery that will physically fit (ie, NS70 X) is not thinking straight. the NS70 X is close on double the capacity of the "stock" unit.
×
×
  • Create New...