Jump to content
SAU Community

Recommended Posts

Hi. My ER34 is running pretty lean at high revs (boosting at 0.8) as data was shown via a dyno. The car is running on stock ECU and I have no plans to upgrade to an aftermarket ECU due to budgetary concerns.

My question is. Could I run a bigger fuel pump (perhaps a factory BNR34 unit) and a fuel regulator to curb this problem?

Or would there be no difference due to the factory ECU has already maxed out the injectors?

Thanks for your comments.

Link to comment
https://www.sau.com.au/forums/topic/222813-running-lean-on-an-er34/
Share on other sites

Most likely the fuel pump is/already is on its way and it will need replacement. Yes replace with a GTR pump and no if its got stock everything no need for a Fuel Reg..

Id recommend a new pump as would most people on the forum as the GTR one will likely fall to the same fate (they are 10 yrs old approx)

The pump should end your problems.

If you are using a bigger turbo for some reason you may need to use a fuel reg to max the injectors. If thats the case perhaps a upgrade is what you need (injectors and ecu)

Edited by DECIM8

DECIM8, yea noted on those used factory BNR34 fuel pump. They may be on its way out too.

Ok, so a new pump is definitly better. Are those from Walbro good enough?

I am running stock turbine. Actually, would a piggy back fuel mangement, say a S-AFC solve my problem or a new fuel pump is the way to go? Fuel regulator isn't necessary?

Because the fuel pump is dying

Its probably the top 10 of Skyline basics.

how is the fuel pump dying if nothings changed from the factory?

::edit::

sorry i didnt realise he was running higher boost, which is still a bit odd, i ran close to 1bar and never had issues.

meh :whistling:

Edited by R34NRG

It could have 200km on the engine, it could have been run very empty many times.. If so its been abused so needs replacing.

Hopefully hes checked his filter first.

Woo I just got my Tomei Pump, man this kit is good comes with new seals and even clips!

how is the fuel pump dying if nothings changed from the factory?

Same way any other pump does - Its called time

Most Nissan pumps fail or perform under par fairly quickly. Part and parcel.

I've had stock pumps fail in factory standard cars before, its nothing new at all

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 2 spots that my exhaust guy joined the 2 pipes together  Made a big difference. I'm now able to live with it. I can make it louder if I want by removing the HKS caps.
    • Hi all, considering clutch upgrade to support 1130 engine hp from 1650cc injectors on e50 at 85% duty cycle (1650 x (11.85/14.7) x 85%). Narrows down to these three as they can be converted to use gm 26 spline input shaft if I ever want to use transmission with that input shaft (orc1000f and r3c easy/cheap just change center hub; tr2cd pricier must change clutch discs). Pricing orc1000f similar to tr2cd, r3c about usd 200 pricier. Orc1000f triple plate 200mm. Tr2cd twin plate 215mm. R3c triple plate 215mm. Claimed max torque : orc 1000f 723 lbs ft; tr2cd 800 lbs ft; r3c 1100 lbs ft. Why orc1000f triple plate but claims lower max torque vs tr2cd twins? Is orc1000f underrated? Any info maxing out these clutches? Info on street/traffic driveability/pedal feel? Thank you for any info on them.
    • Some troubleshooting, connect up a timing light/gun with a proper ignition lead on coil 1. Hold the revs at 4~4500rpm and see if your timing is all over the shop, scattering off its tits. If so, there's a high chance your CAS is fked. But I read you have a Link ECU ready to go in, why not just skip all this and put that in - will make troubleshooting so much easier.  
    • Misfires when the car is fully warm are generally attributed to the coils (and/or the igniter, on cars with a separate igniter). They can stop working properly when they get hot for a number of reasons. Either electric/electronic, or from thermal expansion opening up gaps and allowing HV leakage. Seeing as you have replaced the coils, that could/should rule them out. But I wouldn't always assume so. Were the coils genuine? Or is there a chance you have bought some counterfeit Chinesium shit? Then we're back onto loom connections. They can fail when warm/hot for the same reasons. Inspections, cleaning of contact surfaces, ensuring that terminals are fully inserted, etc etc, are all justified. The same (heat effects) holds true for the other electrics and their connectors. AFM & CAS, primarily. If you try that Chinesium AFM, drive it around on low load until it is properly hot, but do'nt give it more load than you have to, except when you need to see if it will still miss. I'm dead serious about the untrustworthiness of the calibration of those copy AFMs. Injectors are unlikely to get hot unless the fuel is coming back around hot. You could try squirting them with compressed air or freeze spray to cool them back down to see if they are maybe the cause.
    • Alright, all the plugs looks good. Noticed that it starts to get bad when the car is up to temp, that's when things starts to misfire hard. next to do is Injector cleaning and such. Got in touch with a shop to do work on the injectors next Monday also help on diagnosis.
×
×
  • Create New...