Jump to content
SAU Community

Recommended Posts

I was reading on g35driver that some of the cars have been experiencing excessive oil consumption leading to a few blown motors. Seems to be mainly with the RevUp motors? I couldnt find much more info than this as most G35s in the US are new and just go back under warranty.

My question is then what models are mainly affected? I am getting an 05 auto so not sure if this comes with the RevUp motor?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/222918-excessive-oil-consumption/
Share on other sites

i have yet to hear from anyone with a V35 that experiences this oil consumption problem

the original poster of that thread is a person with teriible anxiety so taking what he has said isn't a great resource at all, in fact i don't respond to any of his threads because its frustrating to hear his rubbish!

remember that the yanks on g35driver are more likely to make a fuss to get things through warranty.

it may be that the V35s also suffer this problem or it may be that they don't. we dont know as yet. it may be a number of factors that contribute to any potential problem

the only salvage is that at worse case scenario if you need a new engine or a rebuild, then there are more than enough facilities and parts to do so locally. this is one of the things to risk with buying animport with no warranty.

so far there are over 50 2003/2004 coupe owners on here with NO problems at all in regards to engines

The 2003 350Zs reputedly had an oil consumption issue. Since the engines are near identical, aside from the plastic cover and AFM-to-throttle-body intake tract, I would assume they'd earn a similar reputation.

I haven't heard of anything specifically about V35s, though, and the 350Z oil consumption issue hasn't affected that many owners I know.

its yellow i think

if you stand at the front of the engine bay, its just to the right of the oil cap and has a convoluted path to the sump

Thanks, thats the one I was refering to. Any idea where the auto transmission dipstick is or whether one exists?

i assume the 350z engine was assembled in australia? versus V35 engine assembled in japan?

I'm pretty sure the 350Z is fully imported.

Nissan Australia doesn't have any manufacturing facilities after they stopped making the Pulsar down here, so I'm not sure where they'd assemble anything.

Its probable that Australia's cars are on a custom run from a Japanese factory to ensure they comply with our ADRs so perhaps its only our batch that suffers it. I know the 350Z's intake pipe has a resonator where the US one doesn't, and the ECU tune is probably different for our ADRs.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...