Jump to content
SAU Community

Recommended Posts

Guys this is an E.O.I post. I have recently undergone a left knee reconstruction. Therefore i am unable to use a clutch. I have been able to drive my car for over 3 months. So i have to sell it otherwise it is sitting here getting started and driven round the block by my dad once a week.

However, a change wouldnt go a stray either...and my good old clutch leg should be right to roll in another 2 months or so. Im not sure what i am looking for...so hit me up with what u got!! Im not keen on put much cash on top though...

Factory

*1989 NISSAN SKYLINE HR32 GTS-T M-Spec

*121,000kms

*Black

*Manual

Interior

*Rhino 3 Point immobliser Alarm system

*EL2 Apexi boost gauge

*Turbo Timer

Exterior

**In excellent condition**

**Previously belonged in the Autostyle garage.**

**White r32 gtst wheels

**Fibreglass GTR front bar

**M-spec std side skirts

Engine

*Highflowed R33 turbo built by GCG

*Hybrid Front Mount intercooler with Custom Piping

*3-inch Full exforce exhaust system

*Fuel Cut defender

*Oil catch Can

*Turbosmart Dual stage boost controller

*Apexi power intake (panel filter)

*Compression Test showed 145,146,145,147,145,146 PSI over the 6 cylinders (VERY GOOD SIGN!!)

Drivetrain

*brass button clutch

*relatively new tyres

*All new front end suspension bushes

*lowerred springs

*car was dyno tuned bout 1.5 yrs ago and pulled 210kw@the wheels on 15psi on CNV dyno

Contact:

email me on: [email protected] OR Post on here

Located in Hurstville

Rego Expires 6/JUL/08

Asking Price : $12,000 ONO

Link to comment
https://www.sau.com.au/forums/topic/223107-r32-gtst-mspec-89-for-sale-or-swap/
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...