Jump to content
SAU Community

Recommended Posts

I have an R33 GTST but I figure this question would relate to any model, I am wondering what the effects would be (good/bad/if any) from putting an aftermarket intercooler in whilst leaving the stock turbo installed. I understand that there is no real need, this just came up in conversation the other day and I'd like someone to clarify it for me.

Thanks,

Ive installed one while running stock boost.

I didnt notice anything bad. Ive tested it with my Apexi RSM + Gsensor, and it stills runs very similar times.

However i did notice it slightly change the sound of my blitz BOV.

The reason why i installed it was because i am a uni student, so most of my mods i do on my car have to come in stages due to money restrictions!!

Next few mods will be HD clutch, then onto boost controller/SAFC2 i think! Then off for tune! So the bigger FMIC will be used!

But to answer your questions, in my experience, I didnt notice any negative effects.

The reason why i installed it was because i am a uni student, so most of my mods i do on my car have to come in stages due to money restrictions!!

Same here I am going stage by stage, so i figure once I have finished replacing things like belts, water pump, thermostat etc i'll worry about additions like an intercooler.

Thats another thing I probabley dont need to do things like replace the thermostat but I am for the simple fact I will know its new and works perfectly.

Edited by Nimmo

cooler air hitting your engine, longer engine life, better combustion, better performance on hot days, but slightly more lag

go for a drive, feel the output pipe of your stock cooler, not that cold

find a mate with an aftermarket one, go for a drive, see how much colder it is?

Thanks guys for your input that clariflys everything for me, one other thing joeyjoejoejuniorshabadoo you say not too big I seen many that say they are made for R33's so I guess these are an appropriate size then yeah?.

I also own a 33t... I also have more mods than this but I had the stock turbo with an FMIC and I can tell you there was most certainly a difference. Not one I would assume you would find on a road often but it's possible in an extreme ambient heat you would notice. Though depending on the sizing of the inter cooler you may notice similar issues I did. I have some rather good piping courtesy a shop I am not allowed to mention but if you were to searh posts would find >:P.

Basically I had better response.. infinetly better.. this is due to the fact my inter cooler is not the 3" thick 2x2m monstrosity most have. but you will not find it in a shop.. its a rather limited inter cooler solution which was custom made for someone else who I bought it off. The biggest noticeable difference was on a track my car didn't over heat in 10 seconds but instead gave me the opportunity to find out what else overheats when running wife open for long periods of time. When coupled with a good exhaust the response goes through the roof, coupled with a mammoth inter cooler I would expect the opposite effect on response but equal cooling characteristics.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
    • That worked out PERFECTLY! Thank you big time to JJ. He was able to swap me his stock diff. He drove all the way to me as well. Killer! Removal & install was pretty straightforward. The diff itself is HEAVY. So that’s a 2 man job.  Man does the car drive nice now! Couldn’t have worked out any better 👌
×
×
  • Create New...