Jump to content
SAU Community

Recommended Posts

I`ve driven 800kms today to look at a r33 gts i planned to buy.

I saw that there were something wrong with the offset on the front wheels. And when i measured the wheelbases i found out that the left front wheel was pushed 2.5cm forward.

I werent able to lift the car to take a look under it, so i dont have a clue whats happend to that car.

There wasnt something that interpret that is was crashed. The bodypanels were perfect lined, and couldnt find anything that indicated that it had been smashed and rebuilt.

Anyway, I had to drive the 400km back, without a skyline, so im pretty dissapointed now.

Anyone have a clue what the problem can be ? Should i stay away from that car ?..just let it go ?

Link to comment
https://www.sau.com.au/forums/topic/224582-wheelbase-fault/
Share on other sites

Yes, 2.5 cm is alot. But i was strange that the wheel was pushed forwards. I`ve seen cases there the wheel have been pushed backwards, due to front on collision.

In this case the current owner probaly have reversed into something.

The car is going to be hoisted tomorrow and check wheel alligement on a nissan garage. Have to wait and hear what they say before i make up my mind about this car.

Link to comment
https://www.sau.com.au/forums/topic/224582-wheelbase-fault/#findComment-3976758
Share on other sites

25 mm is a whole heap of wheelbase difference. You sure the factory wheelbase measurements you are using are correct?

Well, when i went to buy the car i saw with my bare eyes that the left front wheel was pushed forwards. The measurement was done with a measuretape, so 2.5cm is only a roughly estimate.

Link to comment
https://www.sau.com.au/forums/topic/224582-wheelbase-fault/#findComment-3976775
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
    • I have too much trauma from every skyline I've ever seen having crushed jack points/pinch welds lol.    Yep, works 100%, it's what I use when I'm using the quick jack. Don't know why I can't also bring myself to do the same thing when I'm using a jack. I blame the skyline PTSD. 
×
×
  • Create New...