Jump to content
SAU Community

Fitting Blitz Injectors To A R34

shnaped_second
 Share

Recommended Posts

shnaped_second Mentor

shnaped_second

Posted
Posted

Bought some Blitz 525cc injectors of greenline and spacers, Part # 31209, got a mechanic to try and fit them to my car but he couldnt get them to fit, said that the orings dont fit and there wouldnt be enough room for them and the fuel rail in between the manifold. So basicly paid $200 to get my old injectors pulled out and put back in. Can anybody help if you have fitted injectors to a r34 please.

Thanks

Brad

Link to comment
https://www.sau.com.au/forums/topic/224595-fitting-blitz-injectors-to-a-r34/
Share on other sites
darrinspencer Grand Master

darrinspencer

Posted
Posted

I just sent you the same info via PM

I took one of my old injectors and the new ones and the fuel rail to a mobile injector guy and got 12 new orings to suit, cost me $20 on a sunday. There was a 6 "green" thicker round orings and 6 black cyclinder shaped orings used.

You need to remove some of the smaller orings that come with them the blitz injectors

I have seen the blitz injectors on Yahoo japan for sale and come with additional orings

I had them in for approx 2000k's with no problems. I have since returned my car back to stock and sold them

No other mods needed. the plugs go staight on. no need to use the supplied plugs.

Fit the spacer between the manifold and fuel rail. I did need to use longer bolts

shnaped_second Mentor

shnaped_second

Posted
  • Author
Posted
*shudder* it is a horrible job to do though, space is limited but it's not impossible...nice to see it's coming along Brad!

Yeah thats why i thought id pay sum1 to do it instead of me, gtrs is fitted just gota get these fitted and my z32 afm and should see around 260rwkw

33_skyline Enthusiast

33_skyline

Posted
Posted

I had the same problem on an R33 S2. (I assume same fuel rail)

Swap the O-rings with the factory injector O-rings.

Once the O-rings are on you will notice a lip above the bottom O-ring (middle injector - purple top)

You can sort of see it in this picture attached.

You need to trim this lip back a little, a set of side cutter pliers will do.

The injectors should then fit, you do also need the blitz injector collers (which you said you bought).

Then you have the injector caps (hold the injector into the fuel rail) they have a little rubber piece underneath that you pull out

and then sits snug on top of the injector

They should sit the same as the stock injectors so shouldn't have a problem with clearance on the plenum top is

back on

If you have anymore questions just ask.

There is also a pic of the injectors installed in my car.

post-35997-1213924220_thumb.jpg

post-35997-1213925119_thumb.jpg

shnaped_second Mentor

shnaped_second

Posted
  • Author
Posted
Need to remove the top of the inlet plenum to get access to the injectors

Yeah he split the manifold in half

I SMS'd you a pick mate.

Thanks mate

I had the same problem on an R33 S2. (I assume same fuel rail)

Swap the O-rings with the factory injector O-rings.

Once the O-rings are on you will notice a lip above the bottom O-ring (middle injector - purple top)

You can sort of see it in this picture attached.

You need to trim this lip back a little, a set of side cutter pliers will do.

The injectors should then fit, you do also need the blitz injector collers (which you said you bought).

Then you have the injector caps (hold the injector into the fuel rail) they have a little rubber piece underneath that you pull out

and then sits snug on top of the injector

They should sit the same as the stock injectors so shouldn't have a problem with clearance on the plenum top is

back on

If you have anymore questions just ask.

There is also a pic of the injectors installed in my car.

pretty much got it all sorted just gota get some Orings now then should be all good

Thanks again guys

666DAN Grand Master

666DAN

Posted
Posted
Yeah he split the manifold in half

Thanks mate

pretty much got it all sorted just gota get some Orings now then should be all good

Thanks again guys

Bah, leave the manifold in place you'll find it's a nice challenge......that's what I keep telling myself :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...