Jump to content
SAU Community

Recommended Posts

1988 Nissan A31 Cefiro

120,000km's

Factory Manual 5 spd

RB20DET

Aircon been regas 3 moths ago

New receiver dyer

Car has original 120000km's on engine and chassis.

Genuine nissan timing belt & water pump done on 105, 000Km

Genuine nissan heater hose amd themostat

13 months registration in VIC till 28/4/2009

hyper gear TR43 Turbo (still under warranty) 225kw @ 1.4 bar (with dyno sheet)

Blitz pod filter

550cc Rx7 INJECTOR

300 Z AFM

040 FUEL PUMP

3" catback system

FMIC

side mount oil cooler and romote oil filter

Nardi Steering wheel

HKS boost gauge

Omoni oil temp, water temp & oil pressure gauges

R33 clutch fan (keep the car cool)

Fields SFC-Hyper R fuel control with display (1/4 time, rev and speedo)

Cusco coilover all around

R32 GTR Sway bar

D - Project caster rod front

Z32 4 pots caliper

rda slot discs

EBC GREEN front pads

Adr Approved Braided Brake Hoses front

17x8 drift tek all around

Front tyres Toyo R888 225/45/17 50%

Rear tyres Advan A048 235/55/17 50%

FRONT LIP AND DUCK TAIL WING

SERIES 2 TAIL LIGHT

HID

AP ENGINEERING PFC

PRICE DROP $11000 ONO

CONTACT ME FOR MORE INFORMATION

0433 409 011

WING

Edited by whyau1
Link to comment
https://www.sau.com.au/forums/topic/224915-cefiro-manual-pfc-for-sell/
Share on other sites

  • 3 weeks later...
  • 1 month later...

can u pm me pics?

are u after a swap .

ive got a r33 skyline with a r34 neo motor, microtech LTX-12, Jic coilovers, big fmic, brand new 1000hp race/drift clutch, lightened fly, lock diff ( NOT WELD) sterio, 60mm alloy 3 core radiator, 17" wheels,

AND MORE

PM me if your keen.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Started sifting thru my brakes to decide which ones I will run on Clem   Made me think I should just put them all on Silver...for when brake fade just isn't an option   Should be able to bump rotor up from 343x32 to 348x36 off Supra. Not sure if the Supra annulus is right for the Alcons or APs but trying g to find a used Supra\M4 rotor to test fit The Alcons seem to gain 1-2mm clearance which all helps  
    • So car is getting a few mods to the cage and some jacking points welded in Meantime Ol Silver gets a new gearbox and shiny clutch.  Old Box is being set aside for Clem  
    • Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
×
×
  • Create New...