Jump to content
SAU Community

Driver's Side Sagging

HuH
 Share

Recommended Posts

HuH Community Regular

HuH

Posted
Posted

Over the last few days I've been having a good fiddle with my suspension setup trying to get the car lower and balanced.

Basically what I've got are standard springs and Bilstein adjustable shocks. The spring seats were on the higher of the two circlip grooves, so I took the shocks out and moved the circlip down to lower the car that little bit. For my first time, it was a seriously annoying process. Eventually I got it all done.

I noticed then that the driver's side was sitting lower than the passenger side. I know that this sag does happen over the life of a car (and mine is 16 years old) so I thought what I'd do is switch the sides over to get it closer to balanced when my body weight is on the driver's side.

So I pulled all the shocks out, and made double triple sure that they were matching heights, and swapped them over.

Anyway, finished that and measured it up again and the driver's side is still sitting lower than the passenger side by about 10-15mm or so at the front (rears are almost identical).

What else can cause this sag? Worn bushes? Something else? Would love any help. Ideally I'd love to get the passenger side sitting down as low as the driver's, but if it's something that's worn then obviously that won't work.

Link to comment
https://www.sau.com.au/forums/topic/225279-drivers-side-sagging/
Share on other sites
Shaun Mentor

Shaun

Posted
Posted

I had the same problem mate. My drivers side was 10mm lower than the PS, so i just compensated by raising and lowering the circlips on the shocks. It now sits even.

I was told that cars of this age flex, sag, twist etc so its not that uncommon. Its unusual, however, that your rears are the same height and its only the front thats sagging. I actually had to work diagonally by raising the DS rear 1 groove and lowering the PS front 1 groove to get my desired height.

Shaun.

madbung Grand Master

madbung

Posted
Posted (edited)

^^^ obviously :D

The difference is generally 3-4mm, park it on a road it'll look level, park on a flat peice of concrete it won't measure level.

Track springs are not the same...tracks have little to no camber, sports springs...some brands are some aren't.

Road springs.....

Edited by madbung
Trav33 Mentor

Trav33

Posted
Posted
Left and right springs when new are generally a different height..it's to allow for the amount of camber built into roads, so the car can track correctly.

I've never heard of this before, i dont think thats true at all.

What car do you know came out with different driver+passenger side springs?

madbung Grand Master

madbung

Posted
Posted (edited)
I've never heard of this before, i dont think thats true at all.

What car do you know came out with different driver+passenger side springs?

Does it sound like something I just made up? Or do you think it may well be something you have never heard about before?

Go search your vast bank of knowledge again, maybe you just missed it.

Answer to the question...all production cars have a bias, whether it's done via springs or other methods (it's so the car can track correctly on cambered roads-thats all roads) unless they have after market suspension.

I really am getting pissed dispensing sound advice, then having to explain it to the third degree.

I think I'll quit..

To the guy with the problem, springs will wear on one side of the car more than the other because it's under more load due to the camber built into roads. So if it's only a couple of mm it's normal.

Edited by madbung
HuH Community Regular

HuH

Posted
  • Author
Posted (edited)

I'm not questioning your theory, I just want to know what's causing it, as it isn't springs in my case. I explained in my first post that I have swapped the shocks and springs over but the drivers side is still sagging lower than the passenger side. My question is, what causes this as it cannot be the springs themselves.

Edited by HuH

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...