Jump to content
SAU Community

Eoi: My Rb26.

BNR32t

By BNR32t,
in Australian Capital Territory

 Share

Recommended Posts

BNR32t Proficient

BNR32t

Posted
Posted

This is an EOI, if you are interested in my short/long motor with or without turbos let me know.

This rb26 is out of my r32 and has down around 8 - 10***k's

Bottem end

Forged bottem end,

r33 gtr crank

Head

Cams

ported

polished

Turbos

HKS25/30s x 2

If your interested let me know and i will give more details.

Keith

Link to comment
https://www.sau.com.au/forums/topic/226834-eoi-my-rb26/
Share on other sites
BNR32t Proficient

BNR32t

Posted
  • Author
Posted

hi guys thanks for the pm's,

Didnt expected any this soon. I will give you guys more info later tonight.

Dont have a heap of time ATM.

Regards

Keith

If i sell the bottem end i wont be going rb26 again.

If i sell the engine i might not go an rb at all :woot:

Link to comment
https://www.sau.com.au/forums/topic/226834-eoi-my-rb26/#findComment-3997685
Share on other sites
BNR32t Proficient

BNR32t

Posted
  • Author
Posted

lol, i have a Windsor and a 6 71 blower :blush:

But i'm not sure what engine yet. not even sure if anyone's going to buy the engine or if i will sell it.

Have to see what happens when i get back to everyone. Sorry it wont be tonight.

Link to comment
https://www.sau.com.au/forums/topic/226834-eoi-my-rb26/#findComment-3998478
Share on other sites
BNR32t Proficient

BNR32t

Posted
  • Author
Posted (edited)

330 odd rwkw's at 15.5 - 16psi. The engine was built with 26-28 psi in mind.

Did a compression test on the weekend. 125psi + or - 5psi over them all. And that was just putting the compression tester in by hand.

This engine hasnt yet had its performance tune, Its currently on its running in tune.

I was advised to put 20k on the lot. But i would prefer just to sell it as a short motor.

Make an offer if your interested. Or pm me for me details on the build

Edited by BNR32t
Link to comment
https://www.sau.com.au/forums/topic/226834-eoi-my-rb26/#findComment-4002655
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...