Jump to content
SAU Community

Eoi: My Rb26.

BNR32t

By BNR32t,
in Australian Capital Territory

 Share

Recommended Posts

BNR32t Proficient

BNR32t

Posted
Posted

This is an EOI, if you are interested in my short/long motor with or without turbos let me know.

This rb26 is out of my r32 and has down around 8 - 10***k's

Bottem end

Forged bottem end,

r33 gtr crank

Head

Cams

ported

polished

Turbos

HKS25/30s x 2

If your interested let me know and i will give more details.

Keith

Link to comment
https://www.sau.com.au/forums/topic/226834-eoi-my-rb26/
Share on other sites
BNR32t Proficient

BNR32t

Posted
  • Author
Posted

hi guys thanks for the pm's,

Didnt expected any this soon. I will give you guys more info later tonight.

Dont have a heap of time ATM.

Regards

Keith

If i sell the bottem end i wont be going rb26 again.

If i sell the engine i might not go an rb at all :woot:

Link to comment
https://www.sau.com.au/forums/topic/226834-eoi-my-rb26/#findComment-3997685
Share on other sites
BNR32t Proficient

BNR32t

Posted
  • Author
Posted

lol, i have a Windsor and a 6 71 blower :blush:

But i'm not sure what engine yet. not even sure if anyone's going to buy the engine or if i will sell it.

Have to see what happens when i get back to everyone. Sorry it wont be tonight.

Link to comment
https://www.sau.com.au/forums/topic/226834-eoi-my-rb26/#findComment-3998478
Share on other sites
BNR32t Proficient

BNR32t

Posted
  • Author
Posted (edited)

330 odd rwkw's at 15.5 - 16psi. The engine was built with 26-28 psi in mind.

Did a compression test on the weekend. 125psi + or - 5psi over them all. And that was just putting the compression tester in by hand.

This engine hasnt yet had its performance tune, Its currently on its running in tune.

I was advised to put 20k on the lot. But i would prefer just to sell it as a short motor.

Make an offer if your interested. Or pm me for me details on the build

Edited by BNR32t
Link to comment
https://www.sau.com.au/forums/topic/226834-eoi-my-rb26/#findComment-4002655
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Christof
      HK Premier with plans for slight mods, but keeping clean and simple

      By Christof · Posted

      First time visitor and currently getting ready to start work on my HK Premier.  Its all stock, 186 with 3 on the tree.  The only mod i have right now is extractors.  I am hoping to get some guidance on slightly modifying the engine to bring a little more power. Just going for a nice, comfortable cruiser.  The car is very straight, however i have been out of the country for 20 years and its been gathering dust at a family farm.  Will be doing quite a bit of body work to cut out some small rust areas (frnt quarter panels and a few other small bits) and fix up the paint.  Will be redoing the interior (its currently black and the seats are in real need of recovering and respringing the driver side (its front bench seat).  The dash needs a little TLC, but no real damage.  As my heater has degraded I am considering fitting something after-market that will be both heater/AC (recommendations here are always welcome). Wanting something discrete that will allow me to use the same controls and not be obvious once inside the car.   For the engine, i have been told i could consider upgrading my cam (imagine i would need a new head as well) and putting a new carby (currently the original stromberg).  However not sure what is going to be the best route.  Would certainly welcome any comments/suggestions.  As  a final step I am looking at changing the wheels. Current hubcaps are in dire need of refurbishment or replacement (imagine its a bit like hens teeth).  Thinking of some clean/classic looking mags (7-inch should be more than enough - not going for a large change in look).  Welcome any comments/advice and of course any questions. 
    • Butters
      Intercooler Choice

      By Butters · Posted

      I got the ARC M079 due to the space constraint.  Been running mint for the last 3 years.  Plazmaman also seems like a really solid choice but not used myself.    Hunt around for a better price but this is what I have - https://www.rhdjapan.com/arc-brazing-intercooler-smic-m079-bnr32.html
    • Toilet Goblin
      Intercooler Choice

      By Toilet Goblin · Posted

      Wanted to follow up on this. Did you end up getting the M073? Still deciding on what to get between nismo m073-79 and plazaman.  
    • funkymonkey
      Crank Motorsports Front Axles

      By funkymonkey · Posted

      I was just watching these boys up in QLD AWD'ing their S13 too.  
    • funkymonkey
      Returning after a long time!

      By funkymonkey · Posted

      Por que no los dos? At least my euro brawler is reliable - unlike the JDMs I've had. Sheraaz you look familiar, did you ever come to an SAU VIC meet aaaaaages ago?
×
×
  • Create New...