Jump to content
SAU Community

Recommended Posts

You may have seen the ad on Tv already and no entries don't close on the 8th or 11th.

Entries for the Sunday 27th show 'n' shine close on the 18th, I confirmed this with John from Shannons who is running the event.

[email protected] or 0417 262 918

Drag Racing is on Saturday 26th running as a street meet $40 entry. Details still to be finalised.

http://www.cadra.com.au/

Have attached all info I have received so far.

So who is coming?

26th_Drags_Nomination_Form.pdf

2008_Motoring_Extravaganza_Flyer.pdf

ENTRY_FORM.doc

LETTER_To_Shannons_Clients.doc

Yep can't wait to smoke some more tyres and maybe get some better times.

CADRA update today, seems its going to be a short meet. Must be to allow for cars to get ready for the show 'n' shine.

post-44657-1215524455_thumb.jpg

  • 2 weeks later...

Pinksta and myself were the only imports at the drags all day. We both beat our old times, the track was very consistent and sticky early in the day.

BK turned up late in the arvo after spark plug problems and did a 11.1 straight up.

I will be at the car show all day tomorrow, see you there.

post-44657-1217082185_thumb.jpg

Not many imports again, but big crowds. Just the orange supra, 300zx and myself showed up I think. Had lots of people looking at, taking photos and asking questions about the Datto.

Anyone get any better shots?

post-44657-1217174872_thumb.jpg

We have to make more of an effort next time!!

I had to work every night! Even my day off!

Was gunna try to get there for an hour or so but slept in all day..

besides, I don't want to "display" Sklyn till she gets the new guards on..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...