Jump to content
SAU Community

Recommended Posts

  • Replies 100
  • Created
  • Last Reply

Top Posters In This Topic

ive had a negative experience with them too...but Jim at CRD is the best skyline tuner in Sydney...by far.

Dont take it to Unique...if anyone wants to know why they can PM me

GTR Tuner, yes. Skyline tuner, negatory.

Im pretty sure someone said it before, CRD is good at GTRS.

Main thing that put me off was the Hot4's silvia blowing up, not the best things to see on a car they tuned and built. Although it may not have been their fault. However this is not why i wont go.

Hitman, gods gift to tuning - so he thinks.

Edited by DECIM8

Hey Nathaniel

which silvia from HOT4s blew up?

i only know of the IgnitionDVD S14.5 owned by Andrew Hawkins, which thought it was an RB26 for a day and shat an oil pump.

but that definatly wasn't CRDs fault

you already know my thoughts on Hitman

I've heard nothing but good things from Unigroup, PowerTune Autstralia, JEM and CRD

Yeah man thats true, I got the impression something else was happening as the way he presented he sounded pissed. I.e they didnt do something, but like I said not the reason I wouldnt go.

Ive got my own reasons ill let you know another time.

Checked out JEM, however they are moving at the months end.

Unigroup is prob my best bet..

Edited by DECIM8

Indy from IS motor racing tune my car also sponsor for Autosalon magazine drift car. Seen my car got tune by Indy my gtr nothing have gone wrong.

you can always give it ago or drop by have a chat to him, his more then happy to help you out .

detail listed below hope that will help ya.

Edited by erwin_skyline

IS Motor Racing (Indy) and Micks Motorsport (Micks) have both tuned my car, and both have been excellent. I've used some of the tuners mentioned in this thread and haven't been impressed with their work.

However - you guys have to remember everyone is biased, and generally if one engine component fails, the tuner is almost always blamed. Threads like this are very hard to keep honest :P No doubt there's some tuners out there that have more bad than good days, but what can you do. I'm hesitant to comment on the companies I didn't like when I used them, but these days everything said on the net' can come back to you, and these guys would have ALL of my details... :down: So f**k that.

Edited by TommO

CV Performance at Taren point.

They have alot of high hp cars and record 1/4 mile times coming out of there.

He doesnt mess around. He's straight to the point, he's quick, and he knows what he's doing.

And they dont charge crazy high prices. Worth a mention.

Edited by Munkyb0y
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...