Jump to content
SAU Community

Recommended Posts

nice job man

have you got an intake routing air in from underneath?

edit: actually i see you're using the stock intercooler, which means you dont have a free hole for the intake.

do you think enough air is getting to the pod through that snorkel?

my theory is :P that the snorkel's mouth is hidden from direct airflow by the bonnet. so the only way to get air through it is if it's sucked in. that wont happen unless the box is well sealed.

Heres my go at it on a R33 ! Cant be much different for a R34 I should think !

post-6582-1218027906_thumb.jpgpost-6582-1218027939_thumb.jpg[attachment=174981:004.jpg

Heres my go at it !

thats the exact kit i was on about....whatd you make it out of and yes, does it have an additional inlet?

Guys air is also pulled into it from behind the front head light. Still working on the side panel that isolates the pod from the engine heat. Reworking the panel as a twin walled partishon with fiberglass in between about 1cm apart. Not happy with pods though cause if any oil gets on your afm the computer reads it as rich and leans it down. Already lost one exhaust scroll that way on a mates car. Went so lean it began to crystalise the cast iron and cracked the hell out of it. Im working on a tripple stock panel filter box arrangement that fits inside the whole thing.

Yes at the moment stock intercoooler but I have a large front mount that plumps back into the original pipe work. A panel sits on top of the intercooler and dirrects air up into the snorkel

  • 4 months later...

that looks great PLYNX

was thinking somtihng like that for my stagea using the snorkle, just to keep that stock look.

didnt have the brain power and patients for it tho, just did the standard box in the corner with air feed from below.

but for air feed, that snorkel was put there by nissan for a reason. so of course it must get air flow.

has anyone had trouble when washing the car. does the high pressure wash go up the air feed into the filter

Its pretty involved and needs a bit of reveres thinking. To make the bit that goes into the snorkel i got a piece of pvc plumbing tubing that fits into the snorkle. Cut two small pieces of the pvc and bolted them to a block of wood. Waxed it and fiberglassed around it. That gives you the oval that fit into the snorkel. Then you take the pvc tube and bolt it to the outside at each end of the oval and fiberglass the underside of the tube and that gives you the revere profile. So now youve got an oval with what looks like two half circles at either end. Then you take a sheet of cardboard and measure out the top shape, transfer it to a sheet of polypropylene( the same stuff that Maccas food trays are made out of ) fiberglass that with a thin sheet so its still flexable. Positon the oval on the lid on the car in the correct height and positon and lightly fiberglass it together. Once thats done build the ramp that goes towards the gard, cut out the underside of the lid so it will feed air from the snorked and the proceed to build up the fibergass to the shape of where the gard and radiator support is.

Thats the simplified version of how its done

Easy ! Well not really ! Just time consuming !

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...