Jump to content
SAU Community

Recommended Posts

Hi

i have a shitload of aftermarket parts for sale i was going to go hektik in my s15 with a rb30/26, and no have deciede im going to buy a house, doing the smart thing

all the engine parts are brand new and some of the bolt on parts are second hand but pretty much brand new.....

i am slightly negotiable on somethings so don't bother with low offers, i simply wont reply....

everything is in Sydney, i have no pics atm but will in the next few days......

most parts are for a rb26

Hypertune intake plenum with 85mm (internal size) throttle body, no fuel rail.......... $ 2300

aeris pistons, on spool rods, assembled, but never used...... $$ 1300

Jun oil pump, only fitted to engine, never used.... $ 1000

RD 28 nissan patrol deisel block,virgin bore, shits all over rb30 blocks, and has piston oil squiters $ 800

rb26 cylinder head, complete minus bolt-on hardware like cas and ignitersd and stuff like that, comes with buckets, valves, shims, caps and rocker covers, has had a hardness test, came back perfect, $ 1200

ACL race bearings, installed then pulled out, never been used $$ 300 for the lot

GTR head studs $ 200

main studs $ 150

stainless steel manifold for rb26 $$ 350

Innovative turbo systems GT80 turbo, rated at 1050 hp at the wheels on a 3l, 80mm front wheel, .96 rear housing with a x trim wheel, silicon nitride bearings, BRAND new $ 3600

Motec m8 ecu has all featuires unlocked like dual band lambaua and also data logging, comes with wiring harness and map sensor

hks cams 272 10.2mm lift inlet and exhaust $ 800

hks valvesprings to suite above $ 400

rb25 gearbox perfect conditioon $ 1100

ati harmonic balancer 1000hp version with water pump pully $$ 800

s15 rear cross member with all r32 gtr acessories, diff, arms, hubs, brakes, everything.... $1500

thats about all for the time bieng, if there is more that crosses my mind ill post it in...

cheers

denis

Edited by den001
Link to comment
https://www.sau.com.au/forums/topic/227385-rb26-rb30-big-hp-parts-for-sale/
Share on other sites

Hey Mate i would like to know how the patrol block works with the 26 head what crank you use what stoke bore size oil pump etc.

Your right in saying that the patrol bloke would handle more as they have a much higher compression then 30's

there is a fair bit of modification to get the head to bolt on, the head bolts are in teh same position, there is a water jacket at the rear of cyl 6 that needs to be welded up and the 3 front oil return lines from he head need to be modified with external lines for drainage, you use teh rb30 crank and these blocks were used to running abour 24:1 comp ratio, they weigh about 40ikgs heavier than a conventional rb30 block, and all that weight is situated in the cylinder bores, so it makes it a optimum block for shitting on 2jz blocks,

there is a fair bit of modification to get the head to bolt on, the head bolts are in teh same position, there is a water jacket at the rear of cyl 6 that needs to be welded up and the 3 front oil return lines from he head need to be modified with external lines for drainage, you use teh rb30 crank and these blocks were used to running abour 24:1 comp ratio, they weigh about 40ikgs heavier than a conventional rb30 block, and all that weight is situated in the cylinder bores, so it makes it a optimum block for shitting on 2jz blocks,

This very interesting, who got you onto using these blocks i say it would be a much better choice then a 30 block even tho you have to mod the water/oil galleries would you know how thick the wall are because if they are pretty thick would be a good idea to bore them out pretty big like to say 92-94mm and make it a 3.4L

So all the mains fit the 30 block

  • 4 months later...

Hi,

I built a RB25/30 with a solid lifter conversion. I intend to replace the RB25DET rocker/plug/camgear covers with RB26DET items. I already have the rocker covers but I still need the sparkplug cover (that goes between the rocker covers in the middle), the front cam gear cover (with the RB26 logo) & also the backing plate that sit between the cam gears and the head.

If you can help, give me a yell at [email protected]

Kind regards

What I did with my RB25/30 was overbore the cylinders and sleeves pressed in, then torque-plate hone the cylinders and also o-ring both the block and head faces. That shits all over the 2JZ in terms of strength as well.

My engine builder recommanded sleeving because it turns out way stronger than using the N1 or the GT blocks, it also gives me the option of punchin them out and installing sleeves with a different bore size if the need arises.

Match that to the forged components on the bottom end along with the extrude honing performed to the head and inlet manifold, this is one invincible donk.

  • 1 year later...
Hi

i have a shitload of aftermarket parts for sale i was going to go hektik in my s15 with a rb30/26, and no have deciede im going to buy a house, doing the smart thing

all the engine parts are brand new and some of the bolt on parts are second hand but pretty much brand new.....

i am slightly negotiable on somethings so don't bother with low offers, i simply wont reply....

everything is in Sydney, i have no pics atm but will in the next few days......

most parts are for a rb26

Hypertune intake plenum with 85mm (internal size) throttle body, no fuel rail.......... $ 2300

aeris pistons, on spool rods, assembled, but never used...... $ 1300

Jun oil pump, only fitted to engine, never used.... $ 1000

RD 28 nissan patrol deisel block,virgin bore, shits all over rb30 blocks, and has piston oil squiters $ 800

rb26 cylinder head, complete minus bolt-on hardware like cas and ignitersd and stuff like that, comes with buckets, valves, shims, caps and rocker covers, has had a hardness test, came back perfect, $ 1200

ACL race bearings, installed then pulled out, never been used $ 300 for the lot

GTR head studs $ 200

main studs $ 150

stainless steel manifold for rb26 $ 350

Innovative turbo systems GT80 turbo, rated at 1050 hp at the wheels on a 3l, 80mm front wheel, .96 rear housing with a x trim wheel, silicon nitride bearings, BRAND new $ 3600

Motec m8 ecu has all featuires unlocked like dual band lambaua and also data logging, comes with wiring harness and map sensor

hks cams 272 10.2mm lift inlet and exhaust $ 800

hks valvesprings to suite above $ 400

rb25 gearbox perfect conditioon $ 1100

ati harmonic balancer 1000hp version with water pump pully $ 800

s15 rear cross member with all r32 gtr acessories, diff, arms, hubs, brakes, everything.... $1500

thats about all for the time bieng, if there is more that crosses my mind ill post it in...

cheers

denis

Hi ther just wondering if you still have the block for sale??? Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...