Jump to content
SAU Community

Recommended Posts

  • Replies 81
  • Created
  • Last Reply

Top Posters In This Topic

Nah seriously if you wanna do a sunrise cruise, 5ish is probably a good start time. And maybe cruise out to the barossa or maybe the back way to Murray Bridge where your facing the sun (bring ya sunnies ;)) so we can cruise along with all the 'lines and see the sunrise :)

For a proper hills run, yeah 3ish :(

Edited by AndrewJZX100

i'm keen for an early morning cruise through the hills. sunrise is normally around 630-7 so kick it off around 5-530 and it will be wicked. i'm normally up then anyway.

has anyone actually driven on an icy road in the hills?

ive lived in the hills all my life and been on my far share of early morning cruises and have never hit any ice on the road.

i did hear that it happened on the freeway once near crafers, but that was after rain aswell. i would be one of the first to say that if it is raining that it isnt the greatest idea to go fanging through the hills and i think that is more of a consideration than ice.

lol, black is is what your tyres feel not what you see.....explanation below:

"Black ice, also known as "glare ice" or "clear ice," typically refers to a thin coating of glazed ice on a surface, often a roadway. While not truly black, it is transparent, allowing the usually-black asphalt/macadam roadway to be seen through it, hence the term. It is unusually slick compared to other forms of roadway ice.

Because it contains relatively little entrapped air in the form of bubbles, black ice is transparent and thus very difficult to see (as compared to snow, frozen slush). In addition, it often is interleaved with wet road, which is identical in appearance. For this reason it is especially hazardous when driving or walking because it is both hard to see and unexpectedly slick.

Bridges and overpasses can be especially dangerous. Black ice forms first on bridges and overpasses because air can circulate both above and below the surface of the elevated roadway, causing the pavement temperature to drop more rapidly. This is often indicated with "Bridge May Be Icy" warning signs.

Black ice may form even when the ambient temperature is several degrees above the NTP freezing point of water (0°C) if the air warms suddenly after a prolonged cold spell that leaves the surface of the roadway well below the freezing point temperature.

The term black ice is sometimes used to describe any type of ice that forms on roadways, even when standing water on roads turns to ice as the temperature falls below freezing."

i've had a run in with (black ice) not too sure if it was! but i use to work at a vineyard in the hills and drove out there at 6 in the morning and i hit this bit of road where you park! i broke and it slowed a little but slid straight into another workers vk commy! not fun

Edited by nos man

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...