Jump to content
SAU Community

Recommended Posts

  • Replies 81
  • Created
  • Last Reply

Top Posters In This Topic

Nah seriously if you wanna do a sunrise cruise, 5ish is probably a good start time. And maybe cruise out to the barossa or maybe the back way to Murray Bridge where your facing the sun (bring ya sunnies ;)) so we can cruise along with all the 'lines and see the sunrise :)

For a proper hills run, yeah 3ish :(

Edited by AndrewJZX100

i'm keen for an early morning cruise through the hills. sunrise is normally around 630-7 so kick it off around 5-530 and it will be wicked. i'm normally up then anyway.

has anyone actually driven on an icy road in the hills?

ive lived in the hills all my life and been on my far share of early morning cruises and have never hit any ice on the road.

i did hear that it happened on the freeway once near crafers, but that was after rain aswell. i would be one of the first to say that if it is raining that it isnt the greatest idea to go fanging through the hills and i think that is more of a consideration than ice.

lol, black is is what your tyres feel not what you see.....explanation below:

"Black ice, also known as "glare ice" or "clear ice," typically refers to a thin coating of glazed ice on a surface, often a roadway. While not truly black, it is transparent, allowing the usually-black asphalt/macadam roadway to be seen through it, hence the term. It is unusually slick compared to other forms of roadway ice.

Because it contains relatively little entrapped air in the form of bubbles, black ice is transparent and thus very difficult to see (as compared to snow, frozen slush). In addition, it often is interleaved with wet road, which is identical in appearance. For this reason it is especially hazardous when driving or walking because it is both hard to see and unexpectedly slick.

Bridges and overpasses can be especially dangerous. Black ice forms first on bridges and overpasses because air can circulate both above and below the surface of the elevated roadway, causing the pavement temperature to drop more rapidly. This is often indicated with "Bridge May Be Icy" warning signs.

Black ice may form even when the ambient temperature is several degrees above the NTP freezing point of water (0°C) if the air warms suddenly after a prolonged cold spell that leaves the surface of the roadway well below the freezing point temperature.

The term black ice is sometimes used to describe any type of ice that forms on roadways, even when standing water on roads turns to ice as the temperature falls below freezing."

i've had a run in with (black ice) not too sure if it was! but i use to work at a vineyard in the hills and drove out there at 6 in the morning and i hit this bit of road where you park! i broke and it slowed a little but slid straight into another workers vk commy! not fun

Edited by nos man

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...