Jump to content
SAU Community

Recommended Posts

Engine is complete and ready to drop in, Makes very impressive power and torque figures. The turbo set-up has been taken off for a new engine im currently building but im throwing in my old T04E and stock exhaust manifold.

Comes with:

Standard N/A rb30 block

Stock 25 Head / inlet

R33 oil pump

gtr N1 water pump

NICS 5 puck ceramic clutch / nismo springs in pressure plate. still bolted upto engine.

Sard injectors 650 cc

Cometic head gasket

New timing belt tensioners

Stock exhaust manifold with T04E

This engine has Zero blow-by.

Does not blow any smoke.

Compression within 5 psi on each cylinder (same to this day as when i built it) Running between 140-145 psi across all 6.

Rev cut was at 6,800 rpm.

serviced every 2000km's with motil competition 15W

Engine was tuned very safely at gt auto garage in brisbane.

Asking $2800 for the whole lot.

Located in Brisbane, Windsor.

Contact on 0413715944.

Cheers Kev.

Edited by kaige
Link to comment
https://www.sau.com.au/forums/topic/228047-rb-30-det-or-2530-engine-for-sale/
Share on other sites

Jeebus/!!!

this is a BARGIN!!

you are mad to sell it for that you should be asking 4 grand.

1 in the hand is woth 2 in the bush, looking for quick easy sale.

This engine will not disappoint

Edited by kaige

making 390 rwhp and 470 nm atw. full boost (17-18 psi) at 3200 rpm.

came on very hard.

did not want to rev this engine past 6800 with stock r33 oil pump and block.

for anyone who comes to have a look i have dyno sheets.

running safe air/fuels and bugger all timming only revving to 6,800.

Edited by kaige
  • 3 weeks later...

OK im going to do a price list for everyone to show you how cheap this is.

rb30e - 250 (complete engine with spark plugs and original timming belt) $250

blown 25 - oil pump, knock sensors, loom and head ect... $1000

head gasket - $250

timming belt and 2 new timming belt tensioners - $230

gtr n1 water pump - $340

gaskets and oil seals, including rear main, crank and both cams - $ 200 at least

clean and check head, new valve stem seals, match head for the 30, add vvt with lines - $550

NICS clutch, has nismo springs and 5 puck button - $540

sard injectors - $600

t04e with dump pipe thrown in as well!

TOTAL $3960

NOT including turbo and labour!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...