Jump to content
SAU Community

Recommended Posts

its really the best he can do, ive heard a few storys with probs at tillbrooks which really werent makrs problem but due to them being his employee's, mark is a good guy, (flew to melb with him for the first drift nats all went to the cas n had a crazy night along with stanic and denzo) good bloke but yer working on his own will be much better!

Edited by shy_s6
its really the best he can do, ive heard a few storys with probs at tillbrooks which really werent makrs problem but due to them being his employee's, mark is a good guy, (flew to melb with him for the first drift nats all went to the cas n had a crazy night along with stanic and denzo) good bloke but yer working on his own will be much better!

Mark is a top guy!! :P

Had good dealing with him when ever he worked on my cars..He hasn't had the best luck with employee's and I am glad he has made the decision to go back to basics :D

Wish him all the best! :banana:

yeah you paid mark to do work on your car and the work got done by the workers thats what workers do when you pay them :/ if he did all the work him self he would never go home so dont be so mellow dramatic

Edited by Bunny33

if his work was so good why is he closing?????? also if mark was a man of his word he would have done as he promised and he DIDN't! so why don't you go and voice your "un educated" opinion elsewhere. oh by the way why don't you go read a dictionary.

Guest
This topic is now closed to further replies.


  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...