Jump to content
SAU Community

Recommended Posts

Okay, so unless I am doing something completely wrong my car just doesn't exist. It has never been made.

I put in my vin. (ECR33-056052), I put in my model number (GGKBRTFR33VDA-U---), I put in my model series number (ECR33), and yet nothing is happening. Just says that my model series and model can't be found for my VIN and that my model and everything else I type in are wrong. Do I need to know something about enterenting this shit? 

I have tried putting ECR33 in the first box and then 056052 in the second box. That didn't work so I tried to put it in as ECR33-056052 but it extended it with all 00000's. Maybe I need to add 0's to mine? What on Earth is going on?

Link to comment
https://www.sau.com.au/forums/topic/228338-nissan-fast-my-car-doesnt-exist/
Share on other sites

Hey, not sure, but it's not coming up in our system, either. Might need some more information about the car to see what's going on here.

Okay, so unless I am doing something completely wrong my car just doesn't exist. It has never been made.

I put in my vin. (ECR33-056052), I put in my model number (GGKBRTFR33VDA-U---), I put in my model series number (ECR33), and yet nothing is happening. Just says that my model series and model can't be found for my VIN and that my model and everything else I type in are wrong. Do I need to know something about enterenting this shit? 

I have tried putting ECR33 in the first box and then 056052 in the second box. That didn't work so I tried to put it in as ECR33-056052 but it extended it with all 00000's. Maybe I need to add 0's to mine? What on Earth is going on?

LOLOL WOW!!! The chassis number AND the VIN number are on OEM Nissan plates UNCHANGED. I can take a damn picture....

Maybe my car is so rare Nissan themselves don't even know about the damn thing...

What information would you need mate?

Edited by AKW

Actually, it isn't R34kid. That is your Chassis Number, AKA your VIN. I asked for the Model Number AKA your Model Number. Look again.

I GOT MY PROGRAM WORKING... okay, I will be running your now R34kid.

Edited by AKW

Ive got a 2001, 2007 and 2008 version of FAST, ill check the VIN when i get home.

One thing I have noticed on the 2008 version is that most, if not all, VINS exported from Japan, aka 'ours', have been removed/deleted. (prob not relevant in this case as most people are using '01 version).

VIN - BCNR33-041211

Model - GGJPRQFR33ZDA-AP-C

Series - R33

Production M/Y - 97/03

Color - KR4

Int Color - K

2k

RB26DETT

HICAS

4WD

MT.F5

thanks mate, what does the 2k stand for? anyone know what the zda - AP and C stand for?

Edited by R34kid

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...