Jump to content
SAU Community

Recommended Posts

S,M,L,XL are kids sizes in the jackets, unfortunately the hoodies start at mens small.

Failing that option, i guess you could get measured up and use the measurements under the sizes on the first page! :(

Thanks for that Damo, I forgot that you had the actual measurements on the 1st page....so here goes:

hoodie/jacket:......................hoodie

username/real name:............SLED

name in caps or not:..............caps as above

colour:..................................black

size:.....................................XL

how many:............................1

I can give you guys cash at Villis or EFT tonight..........whichever you prefer

  • Replies 665
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Here's order number 2 guys:

hoodie/jacket:......................jacket

username/real name:............Daniel

name in caps or not:..............1st letter caps....not the rest "as above"

colour:..................................black

size:.....................................Kidz "10"

how many:............................1

I can give you the cash at Villis for this as well.

is it ok to change my order to this i dont want my name printed on it anymore.

hoodie/jacket:(Jacket)

username/real name: (leave it Blank)

name in caps or not: (leave it Blank)

colour: (Black)

size: (Medium)

how many: (1)

cheers

Allan

Hoodie/Jacket: Jacket

Username/Realname: Whatsisname

Name in CAPS or not: As per above - capital W the rest in lowercase

Colour: Black

Size: Large

How many: 1

Payment ($56.60 )via EFT, tonight.

Thanks.

last day to recieve payments 2morrow!!!orders will be put in monday!!! so dont bother bank transfering sat or sunday!!

CHEERS

hoodie/jacket: Hoodie

username/real name: 260tech

name in caps or not: Not

colour: black

size: S

how many: 1

EFT tonite.

PS: postage est $10 to 6432? Sending $64.20, let me know if this is wrong?

Cheers GW

Edited by 260tech
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...