Jump to content
SAU Community

How To Tell If Its A Push Or Pull Clutch?

R31 Gagz
 Share

Recommended Posts

R31 Gagz Collaborator

R31 Gagz

Posted
Posted (edited)

Hi Everyone,

I have doubts that my 1989 R32 GTR has the original gearbox and clutch, how can I tell for sure whether it's a push or pull type clutch?

I do know it has to do with which side of the clutch fork that the slave cylinder is on, but I cannot find anywhere clarification on which is which. What type of clutch is it, if the slave cylinder is on the engine (or front of car) side of the clutch fork? If I can find this out then it obviously also answers for the opposite side.

Please only post if you know for sure as I've already read enough threads on here and GTROC UK where the information is incomplete or there are conflicting opinions...I need facts!

Thanks to everyone in advance :D

Cheers!

Craig

Edited by R31 Gagz
Duncan Grand Master

Duncan

Posted
Posted

Its dead easy....look at the way the clutch slave rod points.

If it points to the front of the car it is a push clutch. If it points to the rear of the car it is a pull clutch.

So yours is pull if its on the engine side and points rear. Good score in an 89 GTR.

Swiper the Fox Grand Master

Swiper the Fox

Posted
Posted
Its dead easy....look at the way the clutch slave rod points.

If it points to the front of the car it is a push clutch. If it points to the rear of the car it is a pull clutch.

So yours is pull if its on the engine side and points rear. Good score in an 89 GTR.

its the opposite of what is said above.

Swiper the Fox Grand Master

Swiper the Fox

Posted
Posted
good point....I shouldn't stand on my head when looking under the car :thumbsup:

cool...now R31 Gagz...if the rod out of the cylinder is pointing rearwards its a push (actual cylinder is positioned in front of the clutch fork) obviously the other way is pull.

R31 Gagz Collaborator

R31 Gagz

Posted
  • Author
Posted
good point....I shouldn't stand on my head when looking under the car :down:

You had it right...in a way :rofl: ...na thanks mate :D

cool...now R31 Gagz...if the rod out of the cylinder is pointing rearwards its a push (actual cylinder is positioned in front of the clutch fork) obviously the other way is pull.

Thanks DG, that's exactly what I was after :rofl: ...by the way if that's your gtr in your avatar, very nice...read the article on it the other week, 9sec twin low mount....crazy!

Cheers!

Craig

PS...mods, could this thread be stickyd or the information added to an FAQ, it was very hard to find :D....thanks

R31 Gagz Collaborator

R31 Gagz

Posted
  • Author
Posted
Why the difference, are the later pull clutch designs more efficient or better or?

Hi Ben,

Yeah really not sure either, possibly it just works better? The pull type clutches cost slightly more than the pull type, so that's one con...you would hope there were some good pros for paying more :blink:

Does anyone else know why they changed to a pull type clutch on post 1993 model R32 GTRs?

Cheers!

Craig

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Yet another RB Neo misfiring thread after reading all the others.

      By Dose Pipe Sutututu · Posted

      Some troubleshooting, connect up a timing light/gun with a proper ignition lead on coil 1. Hold the revs at 4~4500rpm and see if your timing is all over the shop, scattering off its tits. If so, there's a high chance your CAS is fked. But I read you have a Link ECU ready to go in, why not just skip all this and put that in - will make troubleshooting so much easier.  
    • GTSBoy
      Yet another RB Neo misfiring thread after reading all the others.

      By GTSBoy · Posted

      Misfires when the car is fully warm are generally attributed to the coils (and/or the igniter, on cars with a separate igniter). They can stop working properly when they get hot for a number of reasons. Either electric/electronic, or from thermal expansion opening up gaps and allowing HV leakage. Seeing as you have replaced the coils, that could/should rule them out. But I wouldn't always assume so. Were the coils genuine? Or is there a chance you have bought some counterfeit Chinesium shit? Then we're back onto loom connections. They can fail when warm/hot for the same reasons. Inspections, cleaning of contact surfaces, ensuring that terminals are fully inserted, etc etc, are all justified. The same (heat effects) holds true for the other electrics and their connectors. AFM & CAS, primarily. If you try that Chinesium AFM, drive it around on low load until it is properly hot, but do'nt give it more load than you have to, except when you need to see if it will still miss. I'm dead serious about the untrustworthiness of the calibration of those copy AFMs. Injectors are unlikely to get hot unless the fuel is coming back around hot. You could try squirting them with compressed air or freeze spray to cool them back down to see if they are maybe the cause.
    • uchoa
      Yet another RB Neo misfiring thread after reading all the others.

      By uchoa · Posted

      Alright, all the plugs looks good. Noticed that it starts to get bad when the car is up to temp, that's when things starts to misfire hard. next to do is Injector cleaning and such. Got in touch with a shop to do work on the injectors next Monday also help on diagnosis.
    • fatz
      Beers and skylines Fatz style

      By fatz · Posted

      House of Fatz dry dock needs a clean sadly one of the long time stables is leaving this weekend   see ya mr purple
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      Hence why I've only modified my car into a pure daily. Everything has to remain reliable & roadworthy, while providing value and grin factor. It also must not be handcrafted to the extent that the car will be immovable if something breaks because you cannot get or make a replacement to at least limp around with.
×
×
  • Create New...