Jump to content
SAU Community

Recommended Posts

hey guys, if u culd give me a few pointers on the stock turbos on the r33 '95 model' gts-t.

well the trouble is 4 starters i don't kno anything bout these things, so i dunno if it's alright or not.

well anyways i'v had it since yesterday, an well in 3rd gear u can hear the turbo going, but im not getting all that much power from it,

it just sounds like a big old school fan blowing really hard. lol

an i noticed 2night when in 2nd, i hit bout 3rpm, an then it just magically jumps up2 3.5rpm

then up 2 4rpm.

an the same in 3rd.

should i be worried????????????

HELP. lol

Link to comment
https://www.sau.com.au/forums/topic/229231-possible-turbo-troubles/
Share on other sites

Yeah I'd be guessing clutch slip too.

The first thing I'd be doing is taking it to a mechanic to get it checked over - they might pick up other things that need attention too, and could save you money further down the track. There are plenty around but as with anything, there are good ones and not-so-good ones.

Are you in Brisbane, or elsewhere in Qld?

  • 3 weeks later...

mmk, had a new clutch put in, (it took ages)

anyways after driving from stafford 2 caboolture on the m1, it was all fine till i got 2 the suburbs,

then the tacho started playing up again in 2nd.

i took it 4 a drive up mt mee 2day 2 see if it was slipping but the tacho wouldn't do it?

maybe it is just a dodgy tacho?

any pointers

Does the engine change revs (ie does it sound like the revs match the tacho?) or is the tacho just doing its own thing? If it sounds like the engine is revving when the tacho says it is, it's most likely not a problem with the tacho.

Try this. Out on the highway, drop to 90km/h or so. Put it in 4th and nail it. If the engine picks up a heap of revs (ignore the tacho, you should be able to hear the engine) you most likely have clutch problems. If it doesn't slip, you either have something else wrong, or nothing's wrong and you're just worried about your baby :wave:

If you're really worried about it, I live on the north side of Brissy and I'm happy to come for a drive with you. I'm no expert but I'm happy to look at it?

that would be nice if u could come check it out,

the tacho does it's own thing, i can hear the turbo more then i can hear the rev's of the engine.

but like i said b4 it done it last night but not this morning? whats up with that..?

maybe ur right an i am just paranoid..

Water pump seal? Didn't even know it was busted! But yeah water pump issues can be evil, if it's a decent leak don't drive it anywhere, you most likely won't get any warning on the temperature gauge until it's already done some damage.

Where's the car atm? Ie at your house in Caboolture, or at a workshop, or somewhere else? If you trust people to come to your house (and that's a lot of trust, but it's your call) that might be the best way to do it, that way if it does turn out to be a big problem you don't have far to go. Don't post your address in here obviously though lol. Keep it to PM ;)

the car is at home, cuz i have the company car as well.

yes the water pump seal is leaking but it isn't 2 bad, it's not alot of water wastage.

it is getting replaced either this saturday or the following saturday,

i do still drive it, an it isn't losing much water at all, just mainly when u start it, apart from that, nothing much.

an yes this is my 1st turbo charged car, dantay, but there isn't much boost 2 begin with,

we can all have a look at it on the cruize.

Edited by omy-33
  • 1 month later...

Best thing you can do, cover the intake side of the turbo, where your bleed off for your waste-gate is, put compressed air into that hose and do a intercooler leak test.

Abit hard to explain but that's the ezy way to sus for cooler leak's.

If no air leak, one proplem out the way.

WHITEY

it was doing it b4 i got the fmic in, an it's still doing it. i'v nailed it down 2 the instrument cluster, because it's completely impossible 4 the engine 2 do what it does.

so yea i'v nailed out intercooler troubles, and clutch troubles because i'v had the new 1 put in.

how ever gonna get the transmission looked at and a bearing replaced,

it's sqeeky, an will prob collapse soon, i think it's called a thrust bearing, oh sumthing like that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...