Jump to content
SAU Community

Recommended Posts

Which tyres are good for road + spirited driving and the ocassional drags without burning a hole in my pocket ?

Looking at 235s and 255s

one more thing, whats the largest width that would fit under GTST guards ? both front and rear ?

*thanks guys*

will really appreciate your help. Thanks again !

:burnout:

Link to comment
https://www.sau.com.au/forums/topic/22938-which-tyres-are-good/
Share on other sites

i'm running 275/30/19 in the back falken 451's

they are ok new ..a bit slippy after 5000 k's

Preceda's come in 245/35 only for 19's but have heard some good reviews..about $ 560 ea

i found some hankook k104 's for 400 ae 275/30 but dont know how good they are ...they look huge though :D

Originally posted by EnricoPalazzo

Simex baby! Good for launches!

i had them, they were pretty good.

not i've got a set of the new Dunlop 3000A.

they shit all over the simex. The use them on XR6t/XR8's.

they are very decent.

and what rim size you got?

if you've only got say... 16x8 then it's useless going to 255's

OK I have had the following - all either 235/45/17 or 255/40/17

Goodyear Eagle something - can't remember, cheap, and shit, no grip, but very quiet

Falken GRB FK451 - excellent corner grip, not so great off the line, and still gripped well when worn and pretty quiet

Falken Azenis semi slick - excellent grip when warm, lasted about 6 months, very noisy, not mcuh grip when wet/cold

Falken GRB Tune II - cheap, and it showed - not much grip, in corners or straight line, noisy and lasted about 6000km - but for the money not too bad

Bridgestone S03 - So far so good, heaps of grip in the dry and wet, really quiet - done about 3000km so far and they still look pretty new. On the front now

Bridgestone RE55S - semi slick, heaps of grip - if I can get 10,000km out of them I'll be happy!!, not noisy, good in the wet so far (only 45okms so far!!) No wheelspin in 1st - well priced for what they are, and if you have a bit of grunt, these will get it to the road- so far they are great

And yes, my car gets a thrashing, and goes through its fair share of tyres!! GRB FK451's for value - S03 for pure performance

Hope that helps

dunlop fm-901's are apparently mad. They do well in comparisons such as motor tyre tests.

otherwise maybe try some michelins, my parents have always hed them on their car, and the grip is unbelieveable for the size... not sure which mdel but they wernt even very expensive. WE got P6000's as replacements (on my advide) and the difference in grip is huge, the michelins gripped a million times better...

My friend got 901s for his car in 17/255 17/235 like u, 250 for front and 350 for back from tempe tyres. They are a bit noisy, but excellent grip/handing in wet and dry.

siksII

you got me thinking has anyone done a comparison between top of the line michelin and pirellli tyres on grip

michelin cost over $500 per tyre

pirelli only $380 per tyre

on price for same features I went pirelli but no test drive.

So regarding the michelins can you find out which model?

Are you talking straight line grip or cornering grip?

fm-901's make nice white smoke when they spin and due to their lower grip you feel like your riding harder rubber.

Warning - P-Zeros are very very quiet! although a corner you wouldn't go over 70kph in a brand new volvo you can do at 120kph with PZero's in your skyline, JUST RIDE IT OUT! No drifting!

The time I did that my brakes got too hot and I couldn't slow down enough before the turn. takes about 1 second to drop each 10kph when your brakes are overheating. Freaky.

90 degree left turn - can take at 90kph - 40kph higher than an excel with slightly wider triple sidewall temperature A warmed up tyres. at 50kph.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...